From c0b89ac5bfb90835ef01573267020e42d4fe070c Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?J=C3=B6rg=20Frings-F=C3=BCrst?= Date: Sun, 23 Aug 2015 12:17:05 +0200 Subject: Imported Upstream version 1.8.0 --- doc/dispread.html | 203 ++++++++++++++++++++++++++++++++++++++++++------------ 1 file changed, 159 insertions(+), 44 deletions(-) mode change 100644 => 100755 doc/dispread.html (limited to 'doc/dispread.html') diff --git a/doc/dispread.html b/doc/dispread.html old mode 100644 new mode 100755 index a30ab25..f7fe551 --- a/doc/dispread.html +++ b/doc/dispread.html @@ -45,6 +45,10 @@ + + + + @@ -93,6 +97,10 @@ m + + + + @@ -133,6 +141,10 @@ list + + + + @@ -167,6 +179,10 @@ list + + + + @@ -192,12 +208,20 @@ list + + + + [MSWin] Display via MadVR Video Renderer
 -dcc[:n]             + + + + Display via n'th ChromeCast (default 1, ? for list)
 -s              @@ -381,6 +425,10 @@ Apply + + + + @@ -424,6 +472,10 @@ center, + + + + @@ -463,6 +515,10 @@ normal, + + + + @@ -488,6 +544,10 @@ normal, + + + + @@ -522,6 +582,10 @@ normal, + + + + @@ -546,6 +610,10 @@ normal, + + + + Video encode output as (16-235)/255 "TV" levels
@@ -566,6 +634,10 @@ normal, + + + + Quantize test @@ -582,6 +654,10 @@ fit + + + + in nbits
 rate             @@ -905,6 +1017,10 @@ Both: + + + + Override measured refresh rate with rate Hz
 -M "command"         Invoke shell "command" each time a color is measured
+   -x x                 +Take + manually entered + XYZ values
 -W n|h|x             Override @@ -984,6 +1109,10 @@ n + + + + @@ -1019,6 +1148,10 @@ n + + + + @@ -1116,6 +1249,10 @@ n + + + + @@ -1160,14 +1297,12 @@ n
-dmadvr [MSWin only] causes test patches to be displayed using the MadVR - video renderer. Note that you may have to start the video playback - software and load a video clip in pause for this to work. MadVR - rendering does not need or support VideoLUT access, so the -K option should be used to read calibrated values. - Be aware that the state of the Graphics Card VideoLUTs may affect - the results, and therefore may have to be set appropriately using - dispwin. By default the test patch colors will not be - processed by the MadVR 3dLut (see the -V flag).
+ video renderer. Note that will have to start MadTPG before + running dispread, and that while you can adjust the "Test Pattern + Configuration" controls, you should not normally alter the + "Existing Calibration" controls, as dispread will set these + appropriately. See also -V flag.

-dcc or -dcc:no causes test patches to be displayed using and available installation + falls back to the Default receiver (see installation + + + + instructions for your platform).

-c: The @@ -1388,41 +1527,9 @@ n colorimeter instruments calibration. This will only work with colorimeters that rely on sensor spectral sensitivity calibration information (ie. the X-Rite i1d3, - or the DataColor Spyder4).This -can -improve -a - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - colorimeters accuracy for a particular type of display.
+ or the DataColor Spyder4 & + Spyder 5).This can improve a colorimeters accuracy for a + particular type of display.

The -Q flag allows specifying a tristimulus observer, and is used to compute PCS (Profile Connection Space) @@ -1515,6 +1622,14 @@ a will abort. Note that a test window will also be created on the system running dispread.

+ The -x flag causes dispread to expect + values to be manually entered for each reading, rather than using an + instrument to do the measurements.  This mode is ideal if your + instrument is not supported by Argyll. XYZ values should be entered. + It is possible to navigate about the test values being measured, so + as to do them in any order, as well as re-do values, in case of any + mistakes.
+
The -W n|h|x parameter overrides the default serial communications flow control setting. The value n turns -- cgit v1.2.3