From 22f703cab05b7cd368f4de9e03991b7664dc5022 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?J=C3=B6rg=20Frings-F=C3=BCrst?= Date: Mon, 1 Sep 2014 13:56:46 +0200 Subject: Initial import of argyll version 1.5.1-8 --- spectro/spyd2.c | 3808 +++++++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 3808 insertions(+) create mode 100644 spectro/spyd2.c (limited to 'spectro/spyd2.c') diff --git a/spectro/spyd2.c b/spectro/spyd2.c new file mode 100644 index 0000000..f8f9bac --- /dev/null +++ b/spectro/spyd2.c @@ -0,0 +1,3808 @@ + +/* + * Argyll Color Correction System + * + * Datacolor/ColorVision Spyder 2/3/4 related software. + * + * Author: Graeme W. Gill + * Date: 17/9/2007 + * + * Copyright 2006 - 2013, Graeme W. Gill + * All rights reserved. + * + * (Based initially on i1disp.c) + * + * This material is licenced under the GNU GENERAL PUBLIC LICENSE Version 2 or later :- + * see the License2.txt file for licencing details. + */ + +/* + IMPORTANT NOTES: + + The Spyder 2 instrument cannot function without the driver software + having access to the vendor supplied PLD firmware pattern for it. + This firmware is not provided with Argyll, since it is not available + under a compatible license. + + The purchaser of a Spyder 2 instrument should have received a copy + of this firmware along with their instrument, and should therefore be able to + enable the Argyll driver for this instrument by using the spyd2en utility + to create a spyd2PLD.bin file. + + [ The Spyder 3 & 4 don't need a PLD firmware file. ] + + + The Spyder 4 instrument will not have the full range of manufacturer + calibration settings available without the vendor calibration data. + This calibration day is not provided with Argyll, since it is not + available under a compatible license. + + The purchaser of a Spyder 4 instrument should have received a copy + of this calibration data along with their instrument, and should therefore + be able to enable the use of the full range of calibration settings + by using the spyd4en utility to create a spyd4cal.bin file. + + Alternatively, you can use Argyll .ccss files to set a Spyder 4 + calibration. + + [ The Spyder 2 & 3 don't need a calibration data file. ] + + The hwver == 5 code is not fully implemented. + It's not possible to get it going without an instrument to verify on. + (Perhaps it has only 4 sensors ?) + + The frequency measurement is not very accurate, particularly for + the Spyder 3 & 4, being too low by about 3.5%. + + */ + +/* + If you make use of the instrument driver code here, please note + that it is the author(s) of the code who take responsibility + for its operation. Any problems or queries regarding driving + instruments with the Argyll drivers, should be directed to + the Argyll's author(s), and not to any other party. + + If there is some instrument feature or function that you + would like supported here, it is recommended that you + contact Argyll's author(s) first, rather than attempt to + modify the software yourself, if you don't have firm knowledge + of the instrument communicate protocols. There is a chance + that an instrument could be damaged by an incautious command + sequence, and the instrument companies generally cannot and + will not support developers that they have not qualified + and agreed to support. + */ + +/* TTBD: + + Would be good to add read/write data values if debug >= 3 +*/ + +#include +#include +#include +#include +#include +#include +#include +#include +#ifndef SALONEINSTLIB +#include "copyright.h" +#include "aconfig.h" +#include "numlib.h" +#else /* SALONEINSTLIB */ +#include "sa_config.h" +#include "numsup.h" +#endif /* SALONEINSTLIB */ +#include "xspect.h" +#include "insttypes.h" +#include "conv.h" +#include "icoms.h" +#include "spyd2.h" + +#undef PLOT_SPECTRA /* Plot the sensor senitivity spectra */ +#undef PLOT_SPECTRA_EXTRA /* Plot the sensor senitivity spectra extra values */ +#undef SAVE_SPECTRA /* Save the sensor senitivity spectra to "sensors.sp" */ +#undef SAVE_XYZSPECTRA /* Save the XYZ senitivity spectra to "sensorsxyz.sp" (scale 1.4) */ +#undef SAVE_STDXYZ /* save 1931 2 degree to stdobsxyz.sp */ + + +#define DO_RESETEP /* Do the miscelanous resetep()'s */ +#define CLKRATE 1000000 /* Clockrate the Spyder 2 hardware runs at */ +#define MSECDIV (CLKRATE/1000) /* Divider to turn clocks into msec */ +#define DEFRRATE 50 /* Default display refresh rate */ +#define DO_ADAPTIVE /* Adapt the integration time to the light level */ + /* This helps repeatability at low levels A LOT */ + +#define LEVEL2 /* Second level (nonliniarity) calibration */ +#define RETRIES 4 /* usb_reads are unreliable - bug in spyder H/W ?*/ + +#ifdef DO_ADAPTIVE +# define RINTTIME 2.0 /* Base time to integrate reading over - refresh display */ +# define NINTTIME 2.0 /* Base time to integrate reading over - non-refresh display */ +#else /* !DO_ADAPTIVE */ +# define RINTTIME 5.0 /* Integrate over fixed longer time (manufacturers default) */ +# define NINTTIME 5.0 /* Integrate over fixed longer time (manufacturers default) */ +#endif /* !DO_ADAPTIVE */ + +static inst_code spyd2_interp_code(inst *pp, int ec); + +/* ------------------------------------------------------------------------ */ +/* Implementation */ + +/* Interpret an icoms error into a SPYD2 error */ +static int icoms2spyd2_err(int se) { + if (se != ICOM_OK) + return SPYD2_COMS_FAIL; + return SPYD2_OK; +} + +/* ----------------------------------------------------- */ +/* Big endian wire format conversion routines */ + +/* Take an int, and convert it into a byte buffer big endian */ +static void int2buf(unsigned char *buf, int inv) { + buf[0] = (unsigned char)(inv >> 24) & 0xff; + buf[1] = (unsigned char)(inv >> 16) & 0xff; + buf[2] = (unsigned char)(inv >> 8) & 0xff; + buf[3] = (unsigned char)(inv >> 0) & 0xff; +} + +/* Take a short, and convert it into a byte buffer big endian */ +static void short2buf(unsigned char *buf, int inv) { + buf[0] = (unsigned char)(inv >> 8) & 0xff; + buf[1] = (unsigned char)(inv >> 0) & 0xff; +} + +/* Take a short sized buffer, and convert it to an int big endian */ +static int buf2short(unsigned char *buf) { + int val; + val = buf[0]; + val = ((val << 8) + (0xff & buf[1])); + return val; +} + +/* Take a unsigned short sized buffer, and convert it to an int big endian */ +static int buf2ushort(unsigned char *buf) { + int val; + val = (0xff & buf[0]); + val = ((val << 8) + (0xff & buf[1])); + return val; +} + +/* Take a word sized buffer, and convert it to an int big endian. */ +static int buf2int(unsigned char *buf) { + int val; + val = buf[0]; + val = ((val << 8) + (0xff & buf[1])); + val = ((val << 8) + (0xff & buf[2])); + val = ((val << 8) + (0xff & buf[3])); + return val; +} + +/* Take a word sized buffer, and convert it to an unsigned int big endian. */ +static unsigned int buf2uint(unsigned char *buf) { + unsigned int val; + val = buf[0]; + val = ((val << 8) + (0xff & buf[1])); + val = ((val << 8) + (0xff & buf[2])); + val = ((val << 8) + (0xff & buf[3])); + return val; +} + + +/* Take a 3 byte buffer, and convert it to an unsigned int big endian. */ +static unsigned int buf2uint24(unsigned char *buf) { + unsigned int val; + val = buf[0]; + val = ((val << 8) + (0xff & buf[1])); + val = ((val << 8) + (0xff & buf[2])); + return val; +} + +/* Take a 24 bit unsigned sized buffer in little endian */ +/* format, and return an int */ +static unsigned int buf2uint24le(unsigned char *buf) { + unsigned int val; + val = (0xff & buf[2]); + val = ((val << 8) + (0xff & buf[1])); + val = ((val << 8) + (0xff & buf[0])); + return val; +} + +/* Take a 24 bit unsigned sized buffer in little endian */ +/* nibble swapped format, and return an int */ +static unsigned int buf2uint24lens(unsigned char *buf) { + unsigned int val; + val = (0xf & buf[2]); + val = (val << 4) + (0xf & (buf[2] >> 4)); + val = (val << 4) + (0xf & buf[1]); + val = (val << 4) + (0xf & (buf[1] >> 4)); + val = (val << 4) + (0xf & buf[0]); + val = (val << 4) + (0xf & (buf[0] >> 4)); + return val; +} + +/* Take a 64 sized return buffer, and convert it to a ORD64 */ +static ORD64 buf2ord64(unsigned char *buf) { + ORD64 val; + val = buf[7]; + val = ((val << 8) + (0xff & buf[6])); + val = ((val << 8) + (0xff & buf[5])); + val = ((val << 8) + (0xff & buf[4])); + val = ((val << 8) + (0xff & buf[3])); + val = ((val << 8) + (0xff & buf[2])); + val = ((val << 8) + (0xff & buf[1])); + val = ((val << 8) + (0xff & buf[0])); + return val; +} + +/* ============================================================ */ +/* Low level commands */ + + +/* USB Instrument commands */ + +/* Spyder 2: Reset the instrument */ +static inst_code +spyd2_reset( + spyd2 *p +) { + int se; + int retr; + inst_code rv = inst_ok; + + a1logd(p->log, 3, "spyd2_reset: called\n"); + + for (retr = 0; ; retr++) { + se = p->icom->usb_control(p->icom, + IUSB_ENDPOINT_OUT | IUSB_REQ_TYPE_VENDOR | IUSB_REQ_RECIP_DEVICE, + 0xC7, 0, 0, NULL, 0, 5.0); + + if (se == ICOM_OK) { + a1logd(p->log, 6, "spyd2_reset: complete, ICOM code 0x%x\n",se); + break; + } + if (retr >= RETRIES ) { + a1logd(p->log, 1, "spyd2_reset: failed with ICOM err 0x%x\n",se); + return spyd2_interp_code((inst *)p, icoms2spyd2_err(se)); + } + msec_sleep(500); + a1logd(p->log, 1, "spyd2_reset: reset retry with ICOM err 0x%x\n",se); + } + + return rv; +} + +/* Spyder 2: Get status */ +/* return pointer may be NULL if not needed. */ +static inst_code +spyd2_getstatus( + spyd2 *p, + int *stat /* Return the 1 byte status code */ +) { + unsigned char pbuf[8]; /* status bytes read */ + int _stat; + int se; + int retr; + inst_code rv = inst_ok; + + a1logd(p->log, 3, "spyd2_getstatus: called\n"); + + for (retr = 0; ; retr++) { + se = p->icom->usb_control(p->icom, + IUSB_ENDPOINT_IN | IUSB_REQ_TYPE_VENDOR | IUSB_REQ_RECIP_DEVICE, + 0xC6, 0, 0, pbuf, 8, 5.0); + + if (se == ICOM_OK) + break; + if (retr >= RETRIES ) { + a1logd(p->log, 1, "spyd2_getstatus: failed with ICOM err 0x%x\n",se); + return spyd2_interp_code((inst *)p, icoms2spyd2_err(se)); + } + msec_sleep(500); + a1logd(p->log, 1, "spyd2_getstatus: retry with ICOM err 0x%x\n",se); + } + msec_sleep(100); /* Limit rate status commands can be given */ + + _stat = pbuf[0]; /* Only the first byte is examined. */ + /* Other bytes have information, but SW ignores them */ + + a1logd(p->log, 3, "spyd2_getstatus: returns %d ICOM err 0x%x\n", _stat, se); + + if (stat != NULL) *stat = _stat; + + return rv; +} + +/* Read Serial EEProm bytes (implementation) */ +/* Can't read more than 256 in one go */ +static inst_code +spyd2_readEEProm_imp( + spyd2 *p, + unsigned char *buf, /* Buffer to return bytes in */ + int addr, /* Serial EEprom address, 0 - 1023 */ + int size /* Number of bytes to read, 0 - 128 (ie. max of bank) */ +) { + int se; + int retr; + inst_code rv = inst_ok; + + a1logd(p->log, 3, "spyd2_readEEProm_imp: addr %d, bytes %d\n",addr,size); + + if (addr < 0 + || (p->hwver < 7 && (addr + size) > 512) + || (p->hwver == 7 && (addr + size) > 1024)) + return spyd2_interp_code((inst *)p, SPYD2_BAD_EE_ADDRESS); + + if (size >= 256) + return spyd2_interp_code((inst *)p, SPYD2_BAD_EE_SIZE); + + for (retr = 0; ; retr++) { + se = p->icom->usb_control(p->icom, + IUSB_ENDPOINT_IN | IUSB_REQ_TYPE_VENDOR | IUSB_REQ_RECIP_DEVICE, + 0xC4, addr, size, buf, size, 5.0); + if (se == ICOM_OK) + break; + if (retr >= RETRIES) { + a1logd(p->log, 1, "spyd2_readEEProm_imp: failed with ICOM err 0x%x\n",se); + return spyd2_interp_code((inst *)p, icoms2spyd2_err(se)); + } + msec_sleep(500); + a1logd(p->log, 1, "spyd2_readEEProm_imp: retry with ICOM err 0x%x\n",se); + } + + + a1logd(p->log, 3, "spyd2_readEEProm_imp: returning ICOM err 0x%x\n", se); + + return rv; +} + +/* Read Serial EEProm bytes */ +/* (Handles reads > 256 bytes) */ +static inst_code +spyd2_readEEProm( + spyd2 *p, + unsigned char *buf, /* Buffer to return bytes in */ + int addr, /* Serial EEprom address, 0 - 511 */ + int size /* Number of bytes to read, 0 - 511 */ +) { + + if (addr < 0 + || (p->hwver < 7 && (addr + size) > 512) + || (p->hwver == 7 && (addr + size) > 1024)) + return spyd2_interp_code((inst *)p, SPYD2_BAD_EE_ADDRESS); + + while (size > 255) { /* Single read is too big */ + inst_code rv; + if ((rv = spyd2_readEEProm_imp(p, buf, addr, 255)) != inst_ok) + return rv; + size -= 255; + buf += 255; + addr += 255; + } + return spyd2_readEEProm_imp(p, buf, addr, size); +} + +/* Spyder 2: Download PLD pattern */ +static inst_code +spyd2_loadPLD( + spyd2 *p, + unsigned char *buf, /* Bytes to download */ + int size /* Number of bytes */ +) { + int se; + int retr; + inst_code rv = inst_ok; + + a1logd(p->log, 6, "spyd2_loadPLD: Load PLD %d bytes\n",size); + + for (retr = 0; ; retr++) { + se = p->icom->usb_control(p->icom, + IUSB_ENDPOINT_OUT | IUSB_REQ_TYPE_VENDOR | IUSB_REQ_RECIP_DEVICE, + 0xC0, 0, 0, buf, size, 5.0); + + if (se == ICOM_OK) + break; + if (retr >= RETRIES ) { + a1logd(p->log, 1, "spyd2_loadPLD: failed with ICOM err 0x%x\n",se); + return spyd2_interp_code((inst *)p, icoms2spyd2_err(se)); + } + msec_sleep(500); + a1logd(p->log, 1, "spyd2_loadPLD: retry with ICOM err 0x%x\n",se); + } + + a1logd(p->log, 6, "spyd2_loadPLD: returns ICOM err 0x%x\n", se); + + return rv; +} + +/* Get minmax command. */ +/* Figures out the current minimum and maximum frequency periods */ +/* so as to be able to set a frame detect threshold. */ +/* Note it returns 0,0 if there is not enough light. */ +/* (The light to frequency output period size is inversly */ +/* related to the lightness level) */ +/* (This isn't used by the manufacturers Spyder3/4 driver, */ +/* but the instrument seems to impliment it.) */ +static inst_code +spyd2_GetMinMax( + spyd2 *p, + int *clocks, /* Number of clocks to use (may get limited) */ + int *min, /* Return min and max light->frequency periods */ + int *max +) { + int rwbytes; /* Data bytes read or written */ + int se; + inst_code rv = inst_ok; + int value; + int index; + int retr; + unsigned char buf[8]; /* return bytes read */ + + a1logd(p->log, 2, "spyd2_GetMinMax: %d clocks\n",*clocks); + + /* Issue the triggering command */ + if (*clocks > 0xffffff) + *clocks = 0xffffff; /* Maximum count hardware will take ? */ + value = *clocks >> 8; + value = (value >> 8) | ((value << 8) & 0xff00); /* Convert to big endian */ + index = (*clocks << 8) & 0xffff; + index = (index >> 8) | ((index << 8) & 0xff00); /* Convert to big endian */ + + for (retr = 0; ; retr++) { + /* Issue the trigger command */ + se = p->icom->usb_control(p->icom, + IUSB_ENDPOINT_OUT | IUSB_REQ_TYPE_VENDOR | IUSB_REQ_RECIP_DEVICE, + 0xC2, value, index, NULL, 0, 5.0); + + if ((se != ICOM_OK && retr >= RETRIES)) { + /* Complete the operation so as not to leave the instrument in a hung state */ + msec_sleep(*clocks/MSECDIV); + p->icom->usb_read(p->icom, NULL, 0x81, buf, 8, &rwbytes, 1.0); + + a1logd(p->log, 1, "spyd2_GetMinMax: trig failed with ICOM err 0x%x\n",se); + return spyd2_interp_code((inst *)p, icoms2spyd2_err(se)); + } + if (se != ICOM_OK) { + /* Complete the operation so as not to leave the instrument in a hung state */ + msec_sleep(*clocks/MSECDIV); + p->icom->usb_read(p->icom, NULL, 0x81, buf, 8, &rwbytes, 1.0); + + msec_sleep(500); + a1logd(p->log, 1, "spyd2_GetMinMax: trig retry with ICOM err 0x%x\n",se); + continue; + } + + a1logd(p->log, 3, "spyd2_GetMinMax: trig returns ICOM err 0x%x\n", se); + + /* Allow some time for the instrument to respond */ + msec_sleep(*clocks/MSECDIV); + + /* Now read the bytes */ + se = p->icom->usb_read(p->icom, NULL, 0x81, buf, 8, &rwbytes, 5.0); + if (se == ICOM_OK) + break; + if (retr >= RETRIES) { + a1logd(p->log, 1, "spyd2_GetMinMax: get failed with ICOM err 0x%x\n",se); + return spyd2_interp_code((inst *)p, icoms2spyd2_err(se)); + } + msec_sleep(500); + a1logd(p->log, 1, "spyd2_GetMinMax: get retry with ICOM err 0x%x\n",se); + } + + if (rwbytes != 8) { + a1logd(p->log, 1, "spyd2_GetMinMax: got short data read %d",rwbytes); + return spyd2_interp_code((inst *)p, SPYD2_BADREADSIZE); + } + + *min = buf2ushort(&buf[0]); + *max = buf2ushort(&buf[2]); + + a1logd(p->log, 3, "spyd2_GetMinMax: got %d/%d returns ICOM err 0x%x\n", *min, *max, se); + + return rv; +} + +/* Get refresh rate (low level) command */ +/* (This isn't used by the manufacturers Spyder3 driver, */ +/* but the instrument seems to implement it.) */ +static inst_code +spyd2_GetRefRate_ll( + spyd2 *p, + int *clocks, /* Maximum number of clocks to use */ + int nframes, /* Number of frames to count */ + int thresh, /* Frame detection threshold */ + int *minfclks, /* Minimum number of clocks per frame */ + int *maxfclks, /* Maximum number of clocks per frame */ + int *clkcnt /* Return number of clocks for nframes frames */ +) { + int rwbytes; /* Data bytes read or written */ + int se; + inst_code rv = inst_ok; + int value; + int index; + int flag; + int retr; + unsigned char buf1[8]; /* send bytes */ + unsigned char buf2[8]; /* return bytes read */ + + a1logd(p->log, 3, "spyd2_GetRefRate_ll: %d clocks\n",*clocks); + + /* Setup the triggering parameters */ + if (*clocks > 0xffffff) /* Enforce hardware limits */ + *clocks = 0xffffff; + if (*minfclks > 0x7fff) + *minfclks = 0x7fff; + if (*maxfclks > 0x7fff) + *maxfclks = 0x7fff; + value = *clocks >> 8; + value = (value >> 8) | ((value << 8) & 0xff00); /* Convert to big endian */ + index = (*clocks << 8) & 0xffff; + index = (index >> 8) | ((index << 8) & 0xff00); /* Convert to big endian */ + + /* Setup parameters in send buffer */ + short2buf(&buf1[0], thresh); + short2buf(&buf1[2], nframes); + short2buf(&buf1[4], *minfclks); + short2buf(&buf1[6], *maxfclks); + + /* Issue the triggering command */ + for (retr = 0; ; retr++) { + se = p->icom->usb_control(p->icom, + IUSB_ENDPOINT_OUT | IUSB_REQ_TYPE_VENDOR | IUSB_REQ_RECIP_DEVICE, + 0xC3, value, index, buf1, 8, 5.0); + + if (se != ICOM_OK && retr >= RETRIES) { + /* Complete the operation so as not to leave the instrument in a hung state */ + msec_sleep(*clocks/MSECDIV); + p->icom->usb_read(p->icom, NULL, 0x81, buf2, 8, &rwbytes, 1.0); + + a1logd(p->log, 1, "spyd2_GetRefRate_ll: trig failed with ICOM err 0x%x\n",se); + return spyd2_interp_code((inst *)p, icoms2spyd2_err(se)); + } + if (se != ICOM_OK) { + /* Complete the operation so as not to leave the instrument in a hung state */ + msec_sleep(*clocks/MSECDIV); + p->icom->usb_read(p->icom, NULL, 0x81, buf2, 8, &rwbytes, 1.0); + + msec_sleep(500); + a1logd(p->log, 1, "spyd2_GetRefRate_ll: trig retry with ICOM err 0x%x\n",se); + continue; + } + + a1logd(p->log, 3, "spyd2_GetRefRate_ll: trig returns ICOM err 0x%x\n", se); + + /* Allow some time for the instrument to respond */ + msec_sleep(*clocks/MSECDIV); + + /* Now read the bytes */ + se = p->icom->usb_read(p->icom, NULL, 0x81, buf2, 8, &rwbytes, 5.0); + if (se == ICOM_OK) + break; + if (retr >= RETRIES) { + a1logd(p->log, 3, "spyd2_GetRefRate_ll: get failed with ICOM err 0x%x\n",se); + return spyd2_interp_code((inst *)p, icoms2spyd2_err(se)); + } + msec_sleep(500); + a1logd(p->log, 1, "spyd2_GetRefRate_ll: get retry with ICOM err 0x%x\n",se); + } + + if (rwbytes != 8) { + a1logd(p->log, 1, "spyd2_GetRefRate_ll: got short data read %d",rwbytes); + return spyd2_interp_code((inst *)p, SPYD2_BADREADSIZE); + } + + flag = buf2[0]; + *clkcnt = buf2uint24(&buf2[1]); + + /* Spyder2 */ + if (p->hwver < 4 && flag == 1) { + a1logd(p->log, 1, "spyd2_GetRefRate_ll: got trigger timeout"); + return spyd2_interp_code((inst *)p, SPYD2_TRIGTIMEOUT); + } + + /* Spyder2 */ + if (p->hwver < 4 && flag == 2) { + a1logd(p->log, 1, "spyd2_GetRefRate_ll: got overall timeout"); + return spyd2_interp_code((inst *)p, SPYD2_OVERALLTIMEOUT); + } + + a1logd(p->log, 3, "spyd2_GetRefRate_ll: result %d, returns ICOM err 0x%x\n", *clkcnt, se); + + return rv; +} + +/* Get a reading (low level) command */ +static inst_code +spyd2_GetReading_ll( + spyd2 *p, + int *clocks, /* Nominal/Maximum number of integration clocks to use */ + int nframes, /* Number of refresh frames being measured (not used ?) */ + int thresh, /* Frame detection threshold */ + int *minfclks, /* Minimum number of clocks per frame */ + int *maxfclks, /* Maximum number of clocks per frame */ + double *sensv, /* Return the 8 sensor readings (may be NULL) */ + int *maxtcnt, /* Return the maximum transition count (may be NULL) */ + int *mintcnt /* Return the minimum transition count (may be NULL) */ +) { + int rwbytes; /* Data bytes read or written */ + int se; + inst_code rv = inst_ok; + int value; + int index; + int flag; + int nords, retr; + unsigned char buf1[8]; /* send bytes */ + unsigned char buf2[9 * 8]; /* return bytes read */ + int rvals[3][8]; /* Raw values */ + int _maxtcnt = 0; /* Maximum transition count */ + int _mintcnt = 0x7fffffff; /* Minumum transition count */ + int i, j, k; + + a1logd(p->log, 3, "spyd2_GetReading_ll: clocks = %d, minfc = %d, maxfc = %d\n",*clocks,*minfclks,*maxfclks); + + /* Setup the triggering parameters */ + if (*clocks > 0xffffff) + *clocks = 0xffffff; + if (*minfclks > 0x7fff) + *minfclks = 0x7fff; + if (*maxfclks > 0x7fff) + *maxfclks = 0x7fff; + value = *clocks >> 8; + if (p->hwver == 5) { /* Hmm. not sure if this is right */ + value /= 1000; + } + value = (value >> 8) | ((value << 8) & 0xff00); /* Convert to big endian */ + index = (*clocks << 8) & 0xffff; + index = (index >> 8) | ((index << 8) & 0xff00); /* Convert to big endian */ + + /* Setup parameters in send buffer */ + /* (Spyder3 doesn't seem to use these. Perhaps it does its */ + /* own internal refresh detection and syncronization ?) */ + thresh *= 256; + int2buf(&buf1[0], thresh); + short2buf(&buf1[4], *minfclks); + short2buf(&buf1[6], *maxfclks); + + /* If we aborted a read, the prevraw values are now invalid. */ + /* We fix it by doing a dumy reading. */ + if (p->hwver < 4 && p->prevrawinv) { + int clocks = 500; + int minfclks = 0; + int maxfclks = 0; + p->prevrawinv = 0; + a1logd(p->log, 3, "spyd2_GetReading_ll: doing dummy read to get prevraw\n"); + if ((rv = spyd2_GetReading_ll(p, &clocks, 10, 0, &minfclks, &maxfclks, NULL, NULL, NULL)) != inst_ok) { + a1logd(p->log, 1, "spyd2_GetReading_ll: dummy read failed\n"); + p->prevrawinv = 1; + return rv; + } + } + + /* The Spyder comms seems especially flakey... */ + for (retr = 0, nords = 1; ; retr++, nords++) { + +//int start = msec_time(); + + /* Issue the triggering command */ + se = p->icom->usb_control(p->icom, + IUSB_ENDPOINT_OUT | IUSB_REQ_TYPE_VENDOR | IUSB_REQ_RECIP_DEVICE, + 0xC1, value, index, buf1, 8, 5.0); + + if (se != ICOM_OK && retr >= RETRIES) { + /* Complete the operation so as not to leave the instrument in a hung state */ + msec_sleep(*clocks/MSECDIV); + for (i = 0; i < (1+9); i++) + p->icom->usb_read(p->icom, NULL, 0x81, buf2, 8, &rwbytes, 1.0); + p->prevrawinv = 1; /* prevraw are now invalid */ + + a1logd(p->log, 1, "spyd2_GetReading_ll: trig failed with ICOM err 0x%x\n",se); + return spyd2_interp_code((inst *)p, icoms2spyd2_err(se)); + } + if (se != ICOM_OK) { + /* Complete the operation so as not to leave the instrument in a hung state */ + msec_sleep(*clocks/MSECDIV); + for (i = 0; i < (1+9); i++) + p->icom->usb_read(p->icom, NULL, 0x81, buf2, 8, &rwbytes, 1.0); + p->prevrawinv = 1; /* prevraw are now invalid */ + + msec_sleep(500); + a1logd(p->log, 1, "spyd2_GetReading_ll: trig retry with ICOM err 0x%x\n",se); + continue; + } + + a1logd(p->log, 3, "spyd2_GetReading_ll: reading returns ICOM code 0x%x\n", se); + + /* Allow some time for the instrument to respond */ + msec_sleep(*clocks/MSECDIV); + + /* Now read the first 8 bytes (status etc.) */ + se = p->icom->usb_read(p->icom, NULL, 0x81, buf2, 8, &rwbytes, 5.0); + if (se != ICOM_OK && retr >= RETRIES) { + a1logd(p->log, 1, "spyd2_GetReading_ll: read stat failed with ICOM err 0x%x\n",se); + /* Complete the operation so as not to leave the instrument in a hung state */ + for (i = 0; i < (1+9); i++) + p->icom->usb_read(p->icom, NULL, 0x81, buf2, 8, &rwbytes, 0.5); + p->prevrawinv = 1; /* prevraw are now invalid */ + msec_sleep(500); + + return spyd2_interp_code((inst *)p, icoms2spyd2_err(se)); + } +//printf("~1 trig -> read = %d msec\n",msec_time() - start); + + if (se != ICOM_OK) { + a1logd(p->log, 1, "spyd2_GetReading_ll: read stat retry with ICOM err 0x%x\n", se); + /* Complete the operation so as not to leave the instrument in a hung state */ + for (i = 0; i < (1+9); i++) + p->icom->usb_read(p->icom, NULL, 0x81, buf2, 8, &rwbytes, 0.5); + p->prevrawinv = 1; /* prevraw are now invalid */ + msec_sleep(500); + continue; /* Retry the whole command */ + } + + if (rwbytes != 8) { + a1logd(p->log, 1, "spyd2_GetReading_ll: read stat got short data read %d",rwbytes); + /* Complete the operation so as not to leave the instrument in a hung state */ + for (i = 0; i < (1+9); i++) + p->icom->usb_read(p->icom, NULL, 0x81, buf2, 8, &rwbytes, 0.5); + p->prevrawinv = 1; /* prevraw are now invalid */ + msec_sleep(500); + + return spyd2_interp_code((inst *)p, SPYD2_BADREADSIZE); + } + + flag = buf2[0]; + + /* Spyder2 */ + if (p->hwver < 4 && flag == 1) { + a1logd(p->log, 1, "spyd2_GetReading_ll: read stat is trigger timeout"); + return spyd2_interp_code((inst *)p, SPYD2_TRIGTIMEOUT); + } + + /* Spyder2 */ + if (p->hwver < 4 && flag == 2) { + a1logd(p->log, 1, "spyd2_GetReading_ll: read stat is overall timeout"); + return spyd2_interp_code((inst *)p, SPYD2_OVERALLTIMEOUT); + } + + /* Now read the following 9 x 8 bytes of sensor data */ + for (i = 0; i < 9; i++) { + + se = p->icom->usb_read(p->icom, NULL, 0x81, buf2 + i * 8, 8, &rwbytes, 5.0); + if (se != ICOM_OK && retr >= RETRIES) { + int ii = i; + /* Complete the operation so as not to leave the instrument in a hung state */ + for (; ii < (1+9); ii++) + p->icom->usb_read(p->icom, NULL, 0x81, buf2 + i * 8, 8, &rwbytes, 0.5); + p->prevrawinv = 1; /* prevraw are now invalid */ + + a1logd(p->log, 1, "spyd2_GetReading_ll: get reading failed with ICOM err 0x%x\n",se); + return spyd2_interp_code((inst *)p, icoms2spyd2_err(se)); + } + if (se != ICOM_OK) { + int ii = i; + /* Complete the operation so as not to leave the instrument in a hung state */ + for (; ii < (1+9); ii++) + p->icom->usb_read(p->icom, NULL, 0x81, buf2 + i * 8, 8, &rwbytes, 0.5); + p->prevrawinv = 1; /* prevraw are now invalid */ + + break; + } + if (rwbytes != 8) { + int ii = i; + a1logd(p->log, 1, "spyd2_GetReading_ll: got short data read %d",rwbytes); + + /* Complete the operation so as not to leave the instrument in a hung state */ + for (; ii < (1+9); ii++) + p->icom->usb_read(p->icom, NULL, 0x81, buf2 + i * 8, 8, &rwbytes, 0.5); + p->prevrawinv = 1; /* prevraw are now invalid */ + + return spyd2_interp_code((inst *)p, SPYD2_BADREADSIZE); + } + } + + if (i >= 9) + break; /* We're done */ + + msec_sleep(500); + a1logd(p->log, 1, "spyd2_GetReading_ll: reading retry with ICOM err 0x%x\n",se); + +#ifdef DO_RESETEP /* Do the miscelanous resetep()'s */ + a1logd(p->log, 1, "spyd2_GetReading_ll: resetting end point\n"); + p->icom->usb_resetep(p->icom, 0x81); + msec_sleep(1); /* Let device recover ? */ +#endif /* DO_RESETEP */ + } /* End of whole command retries */ + + if (p->log->debug >= 5) { + a1logd(p->log, 5, "spyd2_GetReading_ll: got bytes:\n"); + for (i = 0; i < 9; i++) { + a1logd(p->log, 5, " %d: 0x%x 0x%x 0x%x 0x%x 0x%x 0x%x 0x%x 0x%x\n",i * 8, + buf2[i * 8 + 0], buf2[i * 8 + 1], buf2[i * 8 + 2], buf2[i * 8 + 3], + buf2[i * 8 + 4], buf2[i * 8 + 5], buf2[i * 8 + 6], buf2[i * 8 + 7]); + } + } + + /* Spyder 2 decoding */ + /* Spyder2 */ + if (p->hwver < 4) { + /* Convert the raw buffer readings into 3 groups of 8 integers. */ + /* At the start of each reading, the HW starts counting master */ + /* (1MHz) clocks. When the first transition after the start of */ + /* the reading is received from a light->frequency sensor (TAOS TSL237), */ + /* the clock count is recorded, and returned as the second of the three */ + /* numbers returned for each sensor. */ + /* When the last transition before the end of the reading period is */ + /* received, the clock count is recorded, and returned as the first */ + /* of the three numbers. The integration period is therefore */ + /* the first number minus the second. */ + /* The third number is the number of transitions from the sensor */ + /* counted during the integration period. Since this 24 bit counter is */ + /* not reset between readings, the previous count is recorded (prevraw[]), */ + /* and subtracted (modulo 24 bits) from the current value. */ + /* The light level is directly proportional to the frequency, */ + /* hence the transitions-1 counted. */ + /* In the case of a CRT, the total number of clocks is assumed to be */ + /* set to an integer number of refresh cycles, and the total transitions */ + /* over that period are counted. */ + for (i = j = 0; j < 3; j++) { + for (k = 0; k < 8; k++, i += 3) { + rvals[j][k] = buf2uint24lens(buf2 + i); +// a1logd(p->log, 1, "got rvals[%d][%d] = 0x%x\n",j,k,rvals[j][k]); + } + } + + /* And convert 3 values per sensor into sensor values */ + for (k = 0; k < 8; k++) { + int transcnt, intclks; + + /* Compute difference of L2F count to previous value */ + /* read, modulo 24 bits */ + a1logd(p->log, 5, "%d: transcnt %d, previous %d\n", k,rvals[2][k],p->prevraw[k]); + if (p->prevraw[k] <= rvals[2][k]) { + transcnt = rvals[2][k] - p->prevraw[k]; + } else { + transcnt = rvals[2][k] + 0x1000000 - p->prevraw[k]; + } + + p->prevraw[k] = rvals[2][k]; /* New previuos value */ + + /* Compute difference of 1MHz clock count of first to second value */ + intclks = rvals[0][k] - rvals[1][k]; + + if (transcnt == 0 || intclks <= 0) { /* It's too dark ... */ + if (sensv != NULL) + sensv[k] = 0.0; + _mintcnt = 0; + } else { /* We discard 0'th L2F transion to give transitions */ + /* over the time period. */ + if (sensv != NULL) + sensv[k] = ((double)transcnt - 1.0) * (double)CLKRATE + / ((double)nords * (double)intclks); + if (transcnt > _maxtcnt) + _maxtcnt = transcnt; + if (transcnt < _mintcnt) + _mintcnt = transcnt; + } + if (p->log->debug >= 4 && sensv != NULL) + a1logd(p->log, 4, "%d: initial senv %f from transcnt %d and intclls %d\n", + k,sensv[k],transcnt,intclks); + +#ifdef NEVER /* This seems to make repeatability worse ??? */ + /* If CRT and bright enough */ + if (sensv != NULL && sensv[k] > 1.5 && p->refrmode != 0) { + sensv[k] = ((double)transcnt) * (double)p->refrate/(double)nframes; + } +#endif + } + + /* Spyder 3/4 decoding */ + } else { + /* Convert the raw buffer readings into 3 groups of 8 integers. */ + /* At the start of each reading, the HW starts counting master */ + /* (1MHz) clocks. When the first transition after the start of */ + /* the reading is received from a light->frequency sensor (TAOS TSL238T), */ + /* the clock count is recorded, and returned as the second of the three */ + /* numbers returned for each sensor. */ + /* When the last transition before the end of the reading period is */ + /* received, the clock count is recorded, and returned as the first */ + /* of the three numbers. The integration period is therefore */ + /* the first number minus the second. */ + /* The third number is the number of transitions from the sensor */ + /* counted during the integration period. */ + /* The light level is directly proportional to the frequency, */ + /* hence the transitions-1 counted. */ + + int map[8] = { 0,0,1,2,5,6,7,4 }; /* Map sensors into Spyder 2 order */ + + for (j = 0; j < 3; j++) { + for (k = 0; k < 8; k++) { + rvals[j][k] = buf2uint24le(buf2 + (j * 24 + map[k] * 3)); +// a1logd(p->log, 1, "got rvals[%d][%d] = 0x%x\n",j,k,rvals[j][k]); + } + } + + /* And convert 3 integers per sensor into sensor values */ + for (k = 0; k < 8; k++) { + int transcnt, intclks; + + /* Number of sensor transitions */ + transcnt = rvals[2][k]; + + /* Compute difference of first integer to second */ + intclks = rvals[0][k] - rvals[1][k]; + + if (transcnt == 0 || intclks <= 0) { /* It's too dark ... */ + if (sensv != NULL) + sensv[k] = 0.0; + _mintcnt = 0; + } else { /* Transitions within integration period */ + /* hence one is discarded ? */ + if (sensv != NULL) + sensv[k] = ((double)transcnt - 1.0) * (double)CLKRATE + / ((double)intclks * 8.125); + if (transcnt > _maxtcnt) + _maxtcnt = transcnt; + if (transcnt < _mintcnt) + _mintcnt = transcnt; + } + if (p->log->debug >= 4 && sensv != NULL) + a1logd(p->log, 4, "%d: initial senv %f from transcnt %d and intclls %d\n", + k,sensv[k],transcnt,intclks); + } + } + + if (maxtcnt != NULL) + *maxtcnt = _maxtcnt; + if (mintcnt != NULL) + *mintcnt = _mintcnt; + + return rv; +} + +/* Spyder 3: Set the LED */ +static inst_code +spyd2_setLED( + spyd2 *p, + int mode, /* LED mode: 0 = off, 1 = pulse, 2 = on */ + double period /* Pulse period in seconds */ +) { + int se; + inst_code rv = inst_ok; + int value; + int index; + int retr; + int ptime; /* Pulse time, 1 - 255 x 20 msec */ + + if (mode < 0) + mode = 0; + else if (mode > 2) + mode = 2; + ptime = (int)(period/0.02 + 0.5); + if (ptime < 0) + ptime = 0; + else if (ptime > 255) + ptime = 255; + + if (p->log->debug >= 2) { + if (mode == 1) + a1logd(p->log, 3, "spyd2_setLED: set to pulse, %f secs\n",ptime * 0.02); + else + a1logd(p->log, 3, "spyd2_setLED: set to %s\n",mode == 0 ? "off" : "on"); + } + + value = mode; /* Leave little endian */ + index = ptime; + + for (retr = 0; ; retr++) { + /* Issue the trigger command */ + se = p->icom->usb_control(p->icom, + IUSB_ENDPOINT_OUT | IUSB_REQ_TYPE_VENDOR | IUSB_REQ_RECIP_DEVICE, + 0xF6, value, index, NULL, 0, 5.0); + + if (se == ICOM_OK) { + a1logd(p->log, 5, "spyd2_setLED: OK, ICOM code 0x%x\n",se); + break; + } + if (retr >= RETRIES) { + a1logd(p->log, 1, "spyd2_setLED: failed with ICOM err 0x%x\n",se); + return spyd2_interp_code((inst *)p, icoms2spyd2_err(se)); + } + msec_sleep(500); + a1logd(p->log, 1, "spyd2_setLED: retry with ICOM err 0x%x\n",se); + } + + return rv; +} + + +/* Spyder 3: Set the ambient control register */ +static inst_code +spyd2_SetAmbReg( + spyd2 *p, + int val /* 8 bit ambient config register value */ +) { + int se; + inst_code rv = inst_ok; + int value; + int retr; + + a1logd(p->log, 3, "spyd2_SetAmbReg: control register to %d\n",val); + + if (val < 0) + val = 0; + else if (val > 255) + val = 255; + value = val; /* Leave little endian */ + + for (retr = 0; ; retr++) { + /* Issue the trigger command */ + se = p->icom->usb_control(p->icom, + IUSB_ENDPOINT_OUT | IUSB_REQ_TYPE_VENDOR | IUSB_REQ_RECIP_DEVICE, + 0xF3, value, 0, NULL, 0, 5.0); + + if (se == ICOM_OK) { + a1logd(p->log, 5, "spyd2_SetAmbReg: OK, ICOM code 0x%x\n",se); + break; + } + if (retr >= RETRIES) { + a1logd(p->log, 1, "spyd2_SetAmbReg: failed with ICOM err 0x%x\n",se); + return spyd2_interp_code((inst *)p, icoms2spyd2_err(se)); + } + msec_sleep(500); + a1logd(p->log, 1, "spyd2_SetAmbReg: retry with ICOM err 0x%x\n",se); + } + + return rv; +} + +/* Spyder3/4: Read ambient light timing */ +/* The byte value seems to be composed of: + bits 0,1 + bits 4 +*/ +static inst_code +spyd2_ReadAmbTiming( + spyd2 *p, + int *val /* Return the 8 bit timing value */ +) { + unsigned char pbuf[1]; /* Timing value read */ + int _val; + int se; + int retr; + inst_code rv = inst_ok; + + a1logd(p->log, 3, "spyd2_ReadAmbTiming: called\n"); + + for (retr = 0; ; retr++) { + se = p->icom->usb_control(p->icom, + IUSB_ENDPOINT_IN | IUSB_REQ_TYPE_VENDOR | IUSB_REQ_RECIP_DEVICE, + 0xF4, 0, 0, pbuf, 1, 5.0); + + if (se == ICOM_OK) + break; + if (retr >= RETRIES) { + a1logd(p->log, 1, "spyd2_ReadAmbTiming: failed with ICOM err 0x%x\n",se); + return spyd2_interp_code((inst *)p, icoms2spyd2_err(se)); + } + msec_sleep(500); + a1logd(p->log, 1, "spyd2_ReadAmbTiming: retry with ICOM err 0x%x\n",se); + } + + _val = pbuf[0]; + + a1logd(p->log, 5, "spyd2_ReadAmbTiming: returning val %d ICOM err 0x%x\n",_val, se); + + if (val != NULL) *val = _val; + + return rv; +} + + +/* Spyder3/4: Read ambient light channel 0 or 1 */ +static inst_code +spyd2_ReadAmbChan( + spyd2 *p, + int chan, /* Ambient channel, 0 or 1 */ + int *val /* Return the 16 bit channel value */ +) { + unsigned char pbuf[2]; /* Channel value read */ + int _val; + int se; + int retr; + inst_code rv = inst_ok; + + chan &= 1; + + a1logd(p->log, 3, "spyd2_ReadAmbChan: channel %d\n",chan); + + for (retr = 0; ; retr++) { + se = p->icom->usb_control(p->icom, + IUSB_ENDPOINT_IN | IUSB_REQ_TYPE_VENDOR | IUSB_REQ_RECIP_DEVICE, + 0xF0 + chan, 0, 0, pbuf, 2, 5.0); + + if (se == ICOM_OK) + break; + if (retr >= RETRIES) { + a1logd(p->log, 2, "spyd2_ReadAmbChan: failed with ICOM err 0x%x\n",se); + return spyd2_interp_code((inst *)p, icoms2spyd2_err(se)); + } + msec_sleep(500); + a1logd(p->log, 2, "spyd2_ReadAmbChan: retry with ICOM err 0x%x\n",se); + } + + _val = buf2ushort(pbuf); + + a1logd(p->log, 3, "spyd2_ReadAmbChan: chan %d returning %d ICOM err 0x%x\n", chan, _val, se); + + if (val != NULL) *val = _val; + + return rv; +} + +/* - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - */ + +/* Spyder3/4: Read temperature config */ +static inst_code +spyd2_ReadTempConfig( + spyd2 *p, + int *val /* Return the 8 bit config value */ +) { + unsigned char pbuf[1]; /* Config value read */ + int _val; + int se; + int retr; + inst_code rv = inst_ok; + + a1logd(p->log, 3, "spyd2_ReadTempConfig: called\n"); + + for (retr = 0; ; retr++) { + se = p->icom->usb_control(p->icom, + IUSB_ENDPOINT_IN | IUSB_REQ_TYPE_VENDOR | IUSB_REQ_RECIP_DEVICE, + 0xE1, 0, 0, pbuf, 1, 5.0); + + if (se == ICOM_OK) + break; + if (retr >= RETRIES) { + a1logd(p->log, 1, "spyd2_ReadTempConfig: failed with ICOM err 0x%x\n",se); + return spyd2_interp_code((inst *)p, icoms2spyd2_err(se)); + } + msec_sleep(500); + a1logd(p->log, 1, "spyd2_ReadTempConfig: retry with ICOM err 0x%x\n",se); + } + + _val = pbuf[0]; + + a1logd(p->log, 3, "spyd2_ReadTempConfig: returning %d ICOM err 0x%x\n", _val, se); + + if (val != NULL) *val = _val; + + return rv; +} + +/* Spyder 3/4: Write Register */ +static inst_code +spyd2_WriteReg( + spyd2 *p, + int reg, + int val /* 8 bit temp config register value */ +) { + int se; + inst_code rv = inst_ok; + int value; + int retr; + + a1logd(p->log, 3, "spyd2_WriteReg: val %d to register %d\n",reg, val); + + if (val < 0) + val = 0; + else if (val > 255) + val = 255; + value = val; /* Leave little endian */ + + reg &= 0xff; + value |= (reg << 8); + + for (retr = 0; ; retr++) { + /* Issue the trigger command */ + se = p->icom->usb_control(p->icom, + IUSB_ENDPOINT_OUT | IUSB_REQ_TYPE_VENDOR | IUSB_REQ_RECIP_DEVICE, + 0xE2, value, 0, NULL, 0, 5.0); + + if (se == ICOM_OK) { + a1logd(p->log, 5, "spyd2_WriteReg: OK, ICOM code 0x%x\n",se); + break; + } + if (retr >= RETRIES) { + a1logd(p->log, 5, "spyd2_WriteReg: failed with ICOM err 0x%x\n",se); + return spyd2_interp_code((inst *)p, icoms2spyd2_err(se)); + } + msec_sleep(500); + a1logd(p->log, 5, "spyd2_WriteReg: retry with ICOM err 0x%x\n",se); + } + + return rv; +} + + +/* Spyder3/4: Read Register */ +static inst_code +spyd2_ReadRegister( + spyd2 *p, + int reg, + int *pval /* Return the register value */ +) { + unsigned char pbuf[2]; /* Temp value read */ + int ival; +// double _val; + int se; + int retr; + inst_code rv = inst_ok; + + reg &= 0xff; + + a1logd(p->log, 3, "spyd2_ReadRegister: register %d\n",reg); + + for (retr = 0; ; retr++) { + se = p->icom->usb_control(p->icom, + IUSB_ENDPOINT_IN | IUSB_REQ_TYPE_VENDOR | IUSB_REQ_RECIP_DEVICE, + 0xE0, reg, 0, pbuf, 2, 5.0); + + if (se == ICOM_OK) + break; + if (retr >= RETRIES) { + a1logd(p->log, 1, "spyd2_ReadRegister: failed with ICOM err 0x%x\n",se); + return spyd2_interp_code((inst *)p, icoms2spyd2_err(se)); + } + msec_sleep(500); + a1logd(p->log, 1, "spyd2_ReadRegister: retry with ICOM err 0x%x\n",se); + } + + ival = buf2ushort(&pbuf[0]); +// _val = (double)ival * 12.5; /* Read temperature */ + + a1logd(p->log, 1, "spyd2_ReadRegister: reg %d returning %d ICOM err 0x%x\n", ival, rv, se); + + if (pval != NULL) *pval = ival; + + return rv; +} + + +/* hwver == 5, set gain */ +/* Valid gain values 1, 4, 16, 64 */ +static inst_code +spyd2_SetGain( + spyd2 *p, + int gain +) { + int gv = 0; + + p->gain = (double)gain; + + switch (gain) { + case 1: + gv = 0; + break; + case 4: + gv = 16; + break; + case 16: + gv = 32; + break; + case 64: + gv = 48; + break; + } + return spyd2_WriteReg(p, 7, gv); +} + +/* ============================================================ */ +/* Medium level commands */ + +/* Read a 8 bits from the EEProm */ +static inst_code +spyd2_rd_ee_uchar( + spyd2 *p, /* Object */ + unsigned int *outp, /* Where to write value */ + int addr /* EEprom Address, 0 - 510 */ +) { + inst_code ev; + unsigned char buf[1]; + + if ((ev = spyd2_readEEProm(p, buf, addr, 1)) != inst_ok) + return ev; + + *outp = buf[0]; + + return inst_ok; +} + +/* Read a 16 bit word from the EEProm */ +static inst_code +spyd2_rd_ee_ushort( + spyd2 *p, /* Object */ + unsigned int *outp, /* Where to write value */ + int addr /* EEprom Address, 0 - 510 */ +) { + inst_code ev; + unsigned char buf[2]; + + if ((ev = spyd2_readEEProm(p, buf, addr, 2)) != inst_ok) + return ev; + + *outp = buf2ushort(buf); + + return inst_ok; +} + +/* Read a 32 bit word from the EEProm */ +static inst_code +spyd2_rd_ee_int( + spyd2 *p, /* Object */ + int *outp, /* Where to write value */ + int addr /* EEprom Address, 0 - 508 */ +) { + inst_code ev; + unsigned char buf[4]; + + if ((ev = spyd2_readEEProm(p, buf, addr, 4)) != inst_ok) + return ev; + + *outp = buf2int(buf); + + return inst_ok; +} + +/* Read a float from the EEProm */ +static inst_code +spyd2_rdreg_float( + spyd2 *p, /* Object */ + double *outp, /* Where to write value */ + int addr /* Register Address, 0 - 508 */ +) { + inst_code ev; + int val; + + if ((ev = spyd2_rd_ee_int(p, &val, addr)) != inst_ok) + return ev; + + *outp = IEEE754todouble((unsigned int)val); + return inst_ok; +} + +unsigned int spyd4_crctab[256]; + +static void spyd4_crc32_init(void) { + int i, j; + + unsigned int crc; + + for (i = 0; i < 256; i++) { + crc = i; + for (j = 0; j < 8; j++) { + if (crc & 1) + crc = (crc >> 1) ^ 0xedb88320; + else + crc = crc >> 1; + } + spyd4_crctab[i] = crc; +// a1logd(p->log, 1, "spyd4_crc32_init: crctab[%d] = 0x%08x\n",i,crctab[i]); + } +} + +static unsigned int spyd4_crc32(unsigned char *data, int len) { + unsigned int crc; + int i; + + crc = ~0; + for (i = 0; i < len; i++) + crc = spyd4_crctab[(crc ^ *data++) & 0xff] ^ (crc >> 8); + return ~crc; +} + +/* For HWV 7, check the EEPRom CRC */ +static inst_code +spyd2_checkEECRC( + spyd2 *p /* Object */ +) { + inst_code ev; + unsigned char buf[1024], *bp; + unsigned int crct, crc; /* Target value, computed value */ + int i; + + spyd4_crc32_init(); + + if ((ev = spyd2_readEEProm(p, buf, 0, 1024)) != inst_ok) + return ev; + + /* Target value */ + crct = buf2uint(buf + 1024 - 4); + + bp = buf; + crc = ~0; + for (i = 0; i < (1024 - 4); i++, bp++) + crc = spyd4_crctab[(crc ^ *bp) & 0xff] ^ (crc >> 8); + crc = ~crc; + + a1logd(p->log, 4, "spyd2_checkEECRC: EEProm CRC is 0x%x, should be 0x%x\n",crc,crct); + + if (crc != crct) + return spyd2_interp_code((inst *)p, SPYD2_BAD_EE_CRC); + + return inst_ok; +} + +/* Special purpose float read, */ +/* Read three 9 vectors of floats from the EEprom */ +static inst_code +spyd2_rdreg_3x9xfloat( + spyd2 *p, /* Object */ + double *out0, /* Where to write first 9 doubles */ + double *out1, /* Where to write second 9 doubles */ + double *out2, /* Where to write third 9 doubles */ + int addr /* Register Address, 0 - 1023 */ +) { + inst_code ev; + unsigned char buf[3 * 9 * 4], *bp; + int i; + + if ((ev = spyd2_readEEProm(p, buf, addr, 3 * 9 * 4)) != inst_ok) + return ev; + + bp = buf; + for (i = 0; i < 9; i++, bp +=4, out0++) { + int val; + val = buf2int(bp); + *out0 = IEEE754todouble((unsigned int)val); + } + + for (i = 0; i < 9; i++, bp +=4, out1++) { + int val; + val = buf2int(bp); + *out1 = IEEE754todouble((unsigned int)val); + } + + for (i = 0; i < 9; i++, bp +=4, out2++) { + int val; + val = buf2int(bp); + *out2 = IEEE754todouble((unsigned int)val); + } + + return inst_ok; +} + +/* Special purpose short read, */ +/* Read 7 x 41 vectors of ints from the EEprom */ +static inst_code +spyd2_rdreg_7x41xshort( + spyd2 *p, /* Object */ + double sens[7][41], /* Destination */ + int addr /* Register Address, 0 - 1023 */ +) { + inst_code ev; + unsigned char buf[7 * 41 * 2], *bp; + int i, j; + + if ((ev = spyd2_readEEProm(p, buf, addr, 7 * 41 * 2)) != inst_ok) + return ev; + + bp = buf; + for (i = 0; i < 7; i++) { + for (j = 0; j < 41; j++, bp += 2) { + int val; + val = buf2ushort(bp); + sens[i][j] = val / 100.0; + } + } + + return inst_ok; +} + +/* Get refresh rate command. Set it to DEFRRATE if not detectable */ +/* if no refresh rate can be established */ +/* (This isn't used by the manufacturers Spyder3/4 driver, */ +/* but the instrument seems to impliment it.) */ +static inst_code +spyd2_read_refrate( + inst *pp, + double *ref_rate +) { + spyd2 *p = (spyd2 *)pp; + inst_code ev; + int clocks; /* Clocks to run commands */ + int min, max; /* min and max light intensity frequency periods */ + + a1logd(p->log, 3, "spyd2_read_refrate: called\n"); + + /* Establish the frame rate detect threshold level */ + clocks = (10 * CLKRATE)/DEFRRATE; + + if ((ev = spyd2_GetMinMax(p, &clocks, &min, &max)) != inst_ok) + return ev; + + if (min == 0 || max < (5 * min)) { + a1logd(p->log, 3, "spyd2_read_refrate: no refresh rate detectable\n"); + if (ref_rate != NULL) + *ref_rate = 0.0; + return inst_ok; + } else { + int frclocks; /* notional clocks per frame */ + int nframes; /* Number of frames to count */ + int thresh; /* Frame detection threshold */ + int minfclks; /* Minimum number of clocks per frame */ + int maxfclks; /* Maximum number of clocks per frame */ + int clkcnt; /* Return number of clocks for nframes frames */ + + frclocks = CLKRATE/DEFRRATE; + nframes = 50; + thresh = (max - min)/5 + min; /* Threshold is at 80% of max brightness */ + minfclks = frclocks/3; /* Allow for 180 Hz */ + maxfclks = (frclocks * 5)/2; /* Allow for 24 Hz */ + clocks = nframes * frclocks * 2; /* Allow for 120 Hz */ + + if ((ev = spyd2_GetRefRate_ll(p, &clocks, nframes, thresh, &minfclks, &maxfclks, + &clkcnt)) != inst_ok) + return ev; + + /* Compute the refresh rate */ + if (ref_rate != NULL) + *ref_rate = ((double)nframes * (double)CLKRATE)/(double)clkcnt; + return inst_ok; + } +} + +/* Get refresh rate command. Set it to DEFRRATE if not detectable */ +/* if no refresh rate can be established */ +/* (This isn't used by the manufacturers Spyder3/4 driver, */ +/* but the instrument seems to impliment it.) */ +static inst_code +spyd2_GetRefRate( + spyd2 *p +) { + int i; + inst_code ev; + + a1logd(p->log, 3, "Frequency calibration called\n"); + + if ((ev = spyd2_read_refrate((inst *)p, &p->refrate)) != inst_ok) { + return ev; + } + if (p->refrate != 0.0) { + a1logd(p->log, 3, "spyd2_GetRefRate: refresh rate is %f Hz\n",p->refrate); + p->refrvalid = 1; + } else { + a1logd(p->log, 3, "spyd2_GetRefRate: no refresh rate detectable\n"); + p->refrate = DEFRRATE; + p->refrvalid = 0; + } + p->rrset = 1; + + return inst_ok; +} + +/* Do a reading. */ +/* Note that the Spyder 3 seems to give USB errors on the data */ +/* read if the measurement time is too small (ie. 0.2 seconds) */ +/* when reading dark values. */ +static inst_code +spyd2_GetReading( + spyd2 *p, + double *XYZ /* return the XYZ values */ +) { + inst_code ev; + int clocks1, clocks2; /* Clocks to run commands */ + int min, max; /* min and max light intensity frequency periods */ + int frclocks; /* notional clocks per frame */ + int nframes; /* Number of frames to measure over */ + int thresh; /* Frame detection threshold */ + int minfclks; /* Minimum number of clocks per frame */ + int maxfclks; /* Maximum number of clocks per frame */ + double sensv[8]; /* The 8 final sensor value readings */ + int maxtcnt; /* The maximum transition count measured */ + int mintcnt; /* The minumum transition count measured */ + double a_sensv[8]; /* Accumulated sensor value readings */ + double a_w[8]; /* Accumulated sensor value weight */ + double pows[9]; /* Power combinations of initial XYZ */ + int i, j, k; + double inttime = 0.0; + + a1logd(p->log, 3, "spyd2_GetReading: called\n"); + + if (p->refrmode) + inttime = RINTTIME; /* ie. 1 second */ + else + inttime = NINTTIME; /* ie. 1 second */ + + /* Compute number of frames for desired base read time */ + nframes = (int)(inttime * p->refrate + 0.5); + + /* Establish the frame rate detect threshold level */ + /* (The Spyder 3 doesn't use this ?) */ + clocks1 = (int)((nframes * CLKRATE)/(10 * p->refrate) + 0.5); /* Use 10% of measurement clocks */ + + if ((ev = spyd2_GetMinMax(p, &clocks1, &min, &max)) != inst_ok) + return ev; + + /* Setup for measurement */ + thresh = (max - min)/5 + min; /* Threshold is at 80% of max brightness */ + if (thresh == 0) + thresh = 65535; /* Set to max, otherwise reading will be 0 */ + frclocks = (int)(CLKRATE/p->refrate + 0.5); /* Nominal clocks per frame */ + minfclks = frclocks/3; /* Allow for 180 Hz */ + maxfclks = (frclocks * 5)/2; /* Allow for 24 Hz */ + + if (p->hwver < 7) { + /* Check calibration is valid */ + if ((p->icx & 1) == 0 && (p->fbits & 1) == 0) { +// return spyd2_interp_code((inst *)p, SPYD2_NOCRTCAL); + a1logd(p->log, 1, "spyd2_GetReading: instrument appears to have no CRT calibration " + "table! Proceeding anyway..\n"); + } + + if ((p->icx & 1) == 1 && (p->fbits & 2) == 0) { +// return spyd2_interp_code((inst *)p, SPYD2_NOLCDCAL); + a1logd(p->log, 1, "spyd2_GetReading: instrument appears to have no LCD calibration " + "table! Proceeding anyway..\n"); + } + } + + a1logd(p->log, 3, "spyd2_GetReading: Using cal table %d\n",(p->icx & 1)); + if (p->hwver) + a1logd(p->log, 3, "spyd2_GetReading: using spectral cal table %d\n",p->icx >> 1); + + for (k = 0; k < 8; k++) /* Zero weighted average */ + a_sensv[k] = a_w[k] = 0.0; + + /* For initial and possible adaptive readings */ + for (i = 0;; i++) { + double itime; /* Integration time */ + + clocks2 = (int)((double)nframes/p->refrate * (double)CLKRATE + 0.5); + + if ((ev = spyd2_GetReading_ll(p, &clocks2, nframes, thresh, &minfclks, &maxfclks, + sensv, &maxtcnt, &mintcnt)) != inst_ok) + return ev; +// a1logd(p->log, 3, "spyd2_GetReading: returned number of clocks = %d\n",clocks2); + + if (p->log->debug >= 3) { + for (k = 0; k < 8; k++) + a1logd(p->log, 3, "Sensor %d value = %f\n",k,sensv[k]); + } + + itime = (double)clocks2 / (double)CLKRATE; +// a1logd(p->log, 3, "spyd2_GetReading: reading %d was %f secs\n",i,itime); + + /* Accumulate it for weighted average */ + for (k = 0; k < 8; k++) { + if (sensv[k] != 0.0) { /* Skip value where we didn't get any transitions */ + a_sensv[k] += sensv[k] * itime; + a_w[k] += itime; + } + } + +#ifdef DO_ADAPTIVE + a1logd(p->log, 3, "spyd2_GetReading: Maxtcnt = %d, Mintcnt = %d\n",maxtcnt,mintcnt); + if (i > 0) + break; /* Done adaptive */ + + /* Decide whether to go around again */ + + if (maxtcnt <= (100/16)) { + nframes *= 16; /* Typically 16 seconds */ + a1logd(p->log, 3, "spyd2_GetReading: using maximum integration time\n"); + } else if (maxtcnt < 100) { + double mulf; + mulf = 100.0/maxtcnt; + mulf -= 0.8; /* Just want to accumulate up to target, not re-do it */ + nframes = (int)(nframes * mulf + 0.5); + a1logd(p->log, 3, "spyd2_GetReading: increasing total integration time " + "by %.1f times\n",1+mulf); + } else { + break; /* No need for another reading */ + } +#else /* !DO_ADAPTIVE */ + a1logw(p->log, "!!!! Spyder 2 DO_ADAPTIVE is off !!!!\n"); + break; +#endif /* !DO_ADAPTIVE */ + } + + /* Compute weighted average and guard against silliness */ + for (k = 0; k < 8; k++) { + if (a_w[k] > 0.0) { + a_sensv[k] /= a_w[k]; + } + } + + if (p->hwver == 5) { + double gainscale = 1.0; + unsigned int v381; + + if ((ev = spyd2_rd_ee_uchar(p, &v381, 381)) != inst_ok) + return ev; + + gainscale = (double)v381/p->gain; + a1logd(p->log, 3, "spyd2_GetReading: hwver5 v381 = %d, gain = %f, gainscale = %f\n", + v381,p->gain,gainscale); + /* Convert sensor readings to XYZ value */ + for (j = 0; j < 3; j++) { + XYZ[j] = p->cal_A[p->icx & 1][j][0]; /* First entry is a constant */ + for (k = 1; k < 8; k++) + XYZ[j] += a_sensv[k] * p->cal_A[p->icx & 1][j][k+2] * gainscale; + } + + } else { + /* Convert sensor readings to XYZ value */ + for (j = 0; j < 3; j++) { + XYZ[j] = p->cal_A[p->icx & 1][j][0]; /* First entry is a constant */ + for (k = 1; k < 8; k++) + XYZ[j] += a_sensv[k] * p->cal_A[p->icx & 1][j][k+1]; + } + } + +// a1logd(p->log, 3, "spyd2_GetReading: real Y = %f\n",XYZ[1]); + a1logd(p->log, 3, "spyd2_GetReading: initial XYZ reading %f %f %f\n",XYZ[0], XYZ[1], XYZ[2]); + +#ifdef LEVEL2 + /* Add "level 2" correction factors */ + pows[0] = XYZ[0]; + pows[1] = XYZ[1]; + pows[2] = XYZ[2]; + pows[3] = XYZ[0] * XYZ[1]; + pows[4] = XYZ[0] * XYZ[2]; + pows[5] = XYZ[1] * XYZ[2]; + pows[6] = XYZ[0] * XYZ[0]; + pows[7] = XYZ[1] * XYZ[1]; + pows[8] = XYZ[2] * XYZ[2]; + + + for (j = 0; j < 3; j++) { + XYZ[j] = 0.0; + + for (k = 0; k < 9; k++) { + XYZ[j] += pows[k] * p->cal_B[p->icx & 1][j][k]; + } + } + a1logd(p->log, 3, "spyd2_GetReading: 2nd level XYZ reading %f %f %f\n",XYZ[0], XYZ[1], XYZ[2]); +#endif + + /* Protect against silliness (This may stuff up averages though!) */ + for (j = 0; j < 3; j++) { + if (XYZ[j] < 0.0) + XYZ[j] = 0.0; + } + a1logd(p->log, 3, "spyd2_GetReading: final XYZ reading %f %f %f\n",XYZ[0], XYZ[1], XYZ[2]); + + return ev; +} + +/* Spyder3/4: Do an ambient reading */ + +/* NOTE :- the ambient sensor is something like a TAOS TLS 2562CS. */ +/* It has two sensors, one wide band and the other infra-red, */ +/* the idea being to subtract them to get a rough human response. */ +/* The reading is 16 bits, and the 8 bit conrol register */ +/* controls gain and integration time: */ + +/* Bits 0,1 inttime, 0 = scale 0.034, 1 = scale 0.252. 2 = scale 1, 3 = manual */ +/* Bit 2, manual, 0 = stop int, 1 = start int */ +/* Bit 4, gain, 0 = gain 1, 1 = gain 16 */ + + +static inst_code +spyd2_GetAmbientReading( + spyd2 *p, + double *XYZ /* return the ambient XYZ values */ +) { + inst_code ev = inst_ok; + int tconf; /* Ambient timing config */ + int iamb0, iamb1; + double amb0, amb1; /* The two ambient values */ + double trv; /* Trial value */ + double thr[8] = { 64/512.0, 128/512.0, 192/512.0, 256/512.0, /* Magic tables */ + 312/512.0, 410/512.0, 666/512.0, 0 }; + double s0[8] = { 498/128.0, 532/128.0, 575/128.0, 624/128.0, + 367/128.0, 210/128.0, 24/128.0, 0 }; + double s1[8] = { 446/128.0, 721/128.0, 891/128.0, 1022/128.0, + 508/128.0, 251/128.0, 18/128.0, 0 }; + double amb; /* Combined ambient value */ + double sfact; + int i; + + a1logd(p->log, 3, "spyd2_GetAmbientReading: called\n"); + + /* Set the ambient control register to 3 */ + if ((ev = spyd2_SetAmbReg(p, 3)) != inst_ok) + return ev; + + /* Wait one second */ + msec_sleep(1000); + + /* Read the ambient timing config value */ + if ((ev = spyd2_ReadAmbTiming(p, &tconf)) != inst_ok) + return ev; +// a1logd(p->log, 4, "spyd2_GetAmbientReading: timing = %d\n",tconf); + + /* Read the ambient values */ + if ((ev = spyd2_ReadAmbChan(p, 0, &iamb0)) != inst_ok) + return ev; + if ((ev = spyd2_ReadAmbChan(p, 1, &iamb1)) != inst_ok) + return ev; + +// a1logd(p->log, 4, "spyd2_GetAmbientReading: values = %d, %d\n",iamb0,iamb1); + amb0 = iamb0/128.0; + amb1 = iamb1/128.0; + + /* Set the ambient control register to 0 */ + if ((ev = spyd2_SetAmbReg(p, 0)) != inst_ok) + return ev; + + /* Compute the scale factor from the timing config value */ + if ((tconf & 3) == 0) + sfact = 1.0/0.034; + else if ((tconf & 3) == 1) + sfact = 1.0/0.252; + else + sfact = 1.0; + + if ((tconf & 0x10) == 0) + sfact *= 16.0; + + amb0 *= sfact; + amb1 *= sfact; + + if (amb0 > 0.0) + trv = amb1/amb0; + else + trv = 0.0; + + for (i = 0; i < 7; i++) { + if (trv <= thr[i]) + break; + } +// a1logd(p->log, 4, "spyd2_GetAmbientReading: trv = %f, s0 = %f, s1 = %f\n",trv, s0[i],s1[i]); + /* Compute ambient in Lux */ + amb = s0[i] * amb0 - s1[i] * amb1; + +// a1logd(p->log, 4, "spyd2_GetAmbientReading: combined ambient = %f Lux\n",amb); + /* Compute the Y value */ + + XYZ[1] = amb; /* cd/m^2 ??? - not very accurate, due to */ + /* spectral response and/or integration angle. */ + XYZ[0] = icmD50.X * XYZ[1]; /* Convert to D50 neutral */ + XYZ[2] = icmD50.Z * XYZ[1]; + + a1logd(p->log, 3, "spyd2_GetAmbientReading: returning %f %f %f\n",XYZ[0],XYZ[1],XYZ[2]); + + return ev; +} + +/* ------------------------------------------------------------ */ +/* Spyder 4 manufacturer calibration data */ +int spyd4_nocals = 0; /* Number of calibrations */ +xspect *spyd4_cals = NULL; /* [nocals] Device spectrum */ + +/* ------------------------------------------------------------ */ +/* Spyder4: Create a calibration matrix using the manufacturers */ +/* calibration data. */ + +static inst_code +spyd4_set_cal( + spyd2 *p, /* Object */ + int ix /* Selection, 0 .. spyd4_nocals-1 */ +) { + int i, j, k; + xspect *oc[3]; /* The XYZ observer curves */ + + if (ix < 0 || ix >= spyd4_nocals) { + return spyd2_interp_code((inst *)p, SPYD2_DISP_SEL_RANGE) ; + } + + /* The Manufacturers calibration routine computes a least squares */ + /* spectral fit of the sensor spectral sensitivities to the */ + /* standard observer curves, weighted by the white illuminant */ + /* of the display technology. We use the same approach for the */ + /* default calibration selections, to be faithful to the Manufacturers */ + /* intentions. */ + + if (standardObserver(oc, icxOT_CIE_1931_2)) { + return spyd2_interp_code((inst *)p, SPYD2_DISP_SEL_RANGE) ; + } + + /* We compute X,Y & Z independently. */ + for (k = 0; k < 3; k++) { + double target[81]; /* Spectral target @ 5nm spacing */ + double **wsens; /* Weighted sensor sensitivities */ + double **psisens; /* Pseudo inverse of sensitivies */ + + /* Load up the observer curve and weight it by the display spectrum */ + /* and mW Lumoinance efficiency factor. */ + for (i = 0; i < 81; i++) { + double nm = 380.0 + i * 5.0; + target[i] = value_xspect(&spyd4_cals[ix], nm) * value_xspect(oc[k], nm) * 0.683002; + } + + /* Load up the sensor curves and weight by the display spectrum */ + wsens = dmatrix(0, 6, 0, 80); + psisens = dmatrix(0, 80, 0, 6); + for (j = 0; j < 7; j++) { + for (i = 0; i < 81; i++) { + double nm = 380.0 + i * 5.0; + wsens[j][i] = value_xspect(&spyd4_cals[ix], nm) * value_xspect(&p->sens[j], nm); + } + } + + /* Compute the pseudo-inverse matrix */ + if (lu_psinvert(psisens, wsens, 7, 81) != 0) { + free_dmatrix(wsens, 0, 6, 0, 80); + free_dmatrix(psisens, 0, 80, 0, 6); + return spyd2_interp_code((inst *)p, SPYD2_CAL_FAIL) ; + } + + { + double *cc, *tt; + p->cal_A[1][k][0] = 0.0; /* Offset is zero */ + p->cal_A[1][k][1] = 0.0; /* Unused is zero */ + cc = &p->cal_A[1][k][2]; /* 7 cal values go here */ + tt = target; + + /* Multiply inverse by target to get calibration matrix */ + if (matrix_mult(&cc, 1, 7, &tt, 1, 81, psisens, 81, 7)) + return spyd2_interp_code((inst *)p, SPYD2_CAL_FAIL) ; + } +// a1logd(p->log, 3, "Cal %d = %f %f %f %f %f %f %f\n", k, p->cal_A[1][k][2], p->cal_A[1][k][3], p->cal_A[1][k][4], p->cal_A[1][k][5], p->cal_A[1][k][6], p->cal_A[1][k][7], p->cal_A[1][k][8]); + } + +#ifdef PLOT_SPECTRA + /* Plot the calibrated sensor spectra */ + { + int i, j, k; + double xx[81]; + double yy[10][81], *yp[10]; + + for (i = 0; i < 81; i++) + xx[i] = 380.0 + i * 5.0; + + for (j = 0; j < 3; j++) { + for (i = 0; i < 81; i++) { + yy[j][i] = 0.0; + for (k = 0; k < 7; k++) { + yy[j][i] += p->cal_A[1][j][k+2] * value_xspect(&p->sens[k], xx[i]); + } + } + yp[j] = yy[j]; + } + for (; j < 10; j++) + yp[j] = NULL; + + printf("The calibrated sensor sensitivities\n"); + do_plot10(xx, yp[0], yp[1], yp[2], yp[3], yp[4], yp[5], yp[6], yp[7], yp[8], yp[9], 81, 0); + } +#endif /* PLOT_SPECTRA */ + +#ifdef SAVE_XYZSPECTRA /* Save the default XYZ senitivity spectra to "sensorsxyz.sp" */ + { + int i, j, k; + xspect xyz[3]; + double wl; + + for (j = 0; j < 3; j++) { + xyz[j].spec_n = 81; + xyz[j].spec_wl_short = 380; + xyz[j].spec_wl_long = 780; + xyz[j].norm = 1.0; + for (i = 0; i < 81; i++) { + wl = 380.0 + i * 5.0; + xyz[j].spec[i] = 0.0; + for (k = 0; k < 7; k++) + xyz[j].spec[i] += p->cal_A[1][j][k+2] * value_xspect(&p->sens[k], wl); + xyz[j].spec[i] *= 1.4; /* Align with std XYZ */ + } + } + write_nxspect("sensorsxyz.sp", xyz, 3, 0); + } +#endif +#ifdef SAVE_STDXYZ + { + xspect xyz[3]; + standardObserver(&xyz[0], &xyz[1], &xyz[2],icxOT_CIE_1931_2); + write_nxspect("stdobsxyz.sp", xyz, 3, 0); + } +#endif /* SAVE_STDXYZ */ + + return inst_ok; +} + + +/* The CCSS calibration uses a set of spectral samples, */ +/* and a least squares matrix is computed to map the sensor RGB */ +/* to the computed XYZ values. This allows better accuracy for */ +/* a typical display that has only 3 degrees of freedom, and */ +/* allows weigting towards a distribution of actual spectral samples. */ +/* Because the typical display has only three degrees of freedom, */ +/* while the instrument has 7 sensors, some extra dummy spectral */ +/* samples are added to the list to provide some slight extra goal. */ + +/* [ Given the poor curve shapes that can come out of this, it's not */ +/* clear that it wouldn't be better using the default flat-spetrum */ +/* calibration and computing a 3x3 calibration matrix over the top of it. ] */ +static inst_code +spyd4_comp_calmat( + spyd2 *p, + icxObserverType obType, /* XYZ Observer type */ + xspect custObserver[3], /* Optional custom observer */ \ + xspect *samples, /* Array of nsamp spectral samples */ + int nsamp /* Number of real samples */ +) { + int i, j; + int nasamp = nsamp + 81; /* Number of real + augmented samples */ + double exwt = 1.0; /* Extra spectral point weight */ + double **sampXYZ; /* Sample XYZ values */ + double **sampSENS; /* Sample Sensor values */ + double **isampSENS; /* Pseudo-inverse of sensor values */ + double **calm; /* Calibration matrix */ + xsp2cie *conv; + double wl; + xspect white; + + if (nsamp < 3) + return spyd2_interp_code((inst *)p, SPYD2_TOO_FEW_CALIBSAMP); + + /* Create white spectrum samples */ + XSPECT_COPY_INFO(&white, &samples[0]); + for (j = 0; j < white.spec_n; j++) + white.spec[j] = 0.0; + for (i = 0; i < nsamp; i++) { + for (j = 0; j < white.spec_n; j++) + if (samples[i].spec[j] > white.spec[j]) + white.spec[j] = samples[i].spec[j]; + } + + /* Compute XYZ of the real sample array. */ + if ((conv = new_xsp2cie(icxIT_none, NULL, obType, custObserver, icSigXYZData, icxClamp)) == NULL) + return spyd2_interp_code((inst *)p, SPYD2_INT_CIECONVFAIL); + sampXYZ = dmatrix(0, nasamp-1, 0, 3-1); + for (i = 0; i < nsamp; i++) { + conv->convert(conv, sampXYZ[i], &samples[i]); +// a1logd(p->log, 3, "asamp[%d] XYZ = %f %f %f\n", i,sampXYZ[nsamp+i][0],sampXYZ[nsamp+i][1], sampXYZ[nsamp+i][2]); + } + + /* Create extra spectral samples */ + for (i = 0; i < 81; i++) { + for (j = 0; j < 3; j++) { + wl = 380.0 + i * 5; + sampXYZ[nsamp+i][j] = exwt * value_xspect(&white, wl) + * value_xspect(&conv->observer[j], wl) * 0.683002; + } +// a1logd(p->log, 3, "asamp[%d] XYZ = %f %f %f\n", i,sampXYZ[nsamp+i][0],sampXYZ[nsamp+i][1], sampXYZ[nsamp+i][2]); + } + conv->del(conv); + + sampSENS = dmatrix(0, nasamp-1, 0, 7-1); + + /* Compute sensor values of the sample array */ + for (i = 0; i < nsamp; i++) { + for (j = 0; j < 7; j++) { + sampSENS[i][j] = 0.0; + for (wl = p->sens[0].spec_wl_short; wl <= p->sens[0].spec_wl_long; wl += 1.0) { + sampSENS[i][j] += value_xspect(&samples[i], wl) * value_xspect(&p->sens[j], wl); + } + } + } + /* Create sensor values of the extra sample array */ + for (i = 0; i < 81; i++) { + for (j = 0; j < 7; j++) { + wl = 380.0 + i * 5; + sampSENS[nsamp+i][j] = exwt * value_xspect(&white, wl) * value_xspect(&p->sens[j], wl); + } +// a1logd(p->log, 3, "asamp[%d] Sens = %f %f %f %f %f %f %f\n", i, +// sampSENS[nsamp+i][0],sampSENS[nsamp+i][1], sampSENS[nsamp+i][2], +// sampSENS[nsamp+i][3],sampSENS[nsamp+i][4], sampSENS[nsamp+i][5], +// sampSENS[nsamp+i][6]); + } +#if defined(PLOT_SPECTRA_EXTRA) + /* Plot the target extra values */ + { + int i, j, k; + double xx[81]; + double yy[10][81], *yp[10]; + + for (i = 0; i < 81; i++) + xx[i] = 380.0 + i * 5; + + for (j = 0; j < 3; j++) { + for (i = 0; i < 81; i++) { + yy[j][i] = sampXYZ[nsamp+i][j]; + } + yp[j] = yy[j]; + } + for (; j < 10; j++) + yp[j] = NULL; + + printf("The target extra XYZ values\n"); + do_plot10(xx, yp[0], yp[1], yp[2], yp[3], yp[4], yp[5], yp[6], yp[7], yp[8], yp[9], 81, 0); + + for (j = 0; j < 7; j++) { + for (i = 0; i < 81; i++) { + yy[j][i] = sampSENS[nsamp+i][j]; + } + yp[j] = yy[j]; + } + for (; j < 10; j++) + yp[j] = NULL; + + printf("The given extra sensor values\n"); + do_plot10(xx, yp[0], yp[1], yp[2], yp[3], yp[4], yp[5], yp[6], yp[7], yp[8], yp[9], 81, 0); + } +#endif /* PLOT_SPECTRA_EXTRA */ + + + isampSENS = dmatrix(0, 7-1, 0, nasamp-1); + + /* Compute the pseudo inverse of sampSENS */ + if (lu_psinvert(isampSENS, sampSENS, nasamp, 7) != 0) { + free_dmatrix(sampXYZ, 0, nasamp-1, 0, 3-1); + free_dmatrix(sampSENS, 0, nasamp-1, 0, 7-1); + free_dmatrix(isampSENS, 0, 7-1, 0, nasamp-1); + return spyd2_interp_code((inst *)p, SPYD2_CAL_FAIL) ; + } + + calm = dmatrix(0, 7-1, 0, 3-1); + + /* Multiply inverse by target to get calibration matrix */ + if (matrix_mult(calm, 7, 3, isampSENS, 7, nasamp, sampXYZ, nasamp, 3)) { + free_dmatrix(sampXYZ, 0, nasamp-1, 0, 3-1); + free_dmatrix(sampSENS, 0, nasamp-1, 0, 7-1); + free_dmatrix(isampSENS, 0, 7-1, 0, nasamp-1); + free_dmatrix(calm, 0, 7-1, 0, 3-1); + return spyd2_interp_code((inst *)p, SPYD2_CAL_FAIL); + } + + /* Copy the matrix into place */ + for (i = 0; i < 7; i++) { + for (j = 0; j < 3; j++) { +//calm[i][j] = 0.5; + p->cal_A[1][j][2+i] = calm[i][j]; + } + } + + free_dmatrix(calm, 0, 7-1, 0, 3-1); + +#ifdef NEVER + + /* Compute the residuals */ + { + double **refXYZ; + double t1, t2; + + refXYZ = dmatrix(0, nasamp-1, 0, 3-1); + + if (matrix_mult(refXYZ, nasamp, 3, sampSENS, nasamp, 7, calm, 7, 3)) { + printf("Residual matrix mult failed\n"); + } else { + t1 = 0.0; + for (i = 0; i < nsamp; i++) { + t1 += icmLabDE(refXYZ[i],sampXYZ[i]); + } + t1 /= nsamp; + printf("Average error for sample points = %f\n",t1); + t2 = 0.0; + for (i = nsamp; i < (nsamp + 81); i++) { + t2 += icmLabDE(refXYZ[i],sampXYZ[i]); +// printf("Resid %d error = %f, %f %f %f, %f %f %f\n", +// i, icmLabDE(refXYZ[i],sampXYZ[i]), sampXYZ[i][0], sampXYZ[i][1], +// sampXYZ[i][2], refXYZ[i][0], refXYZ[i][1], refXYZ[i][2]); + } + t2 /= 81; + printf("Average error for extra points = %f\n",t2); + } + } +#endif + +#ifdef PLOT_SPECTRA + /* Plot the calibrated sensor spectra */ + { + int i, j, k; + double xx[81]; + double yy[10][81], *yp[10]; + + for (i = 0; i < 81; i++) + xx[i] = 380.0 + i * 5.0; + + for (j = 0; j < 3; j++) { + for (i = 0; i < 81; i++) { + yy[j][i] = 0.0; + for (k = 0; k < 7; k++) { + yy[j][i] += p->cal_A[1][j][k+2] * value_xspect(&p->sens[k], xx[i]); + } + } + yp[j] = yy[j]; + } + for (; j < 10; j++) + yp[j] = NULL; + + printf("The calibrated sensor sensitivities\n"); + do_plot10(xx, yp[0], yp[1], yp[2], yp[3], yp[4], yp[5], yp[6], yp[7], yp[8], yp[9], 81, 0); + } +#endif /* PLOT_SPECTRA */ + + free_dmatrix(sampXYZ, 0, nasamp-1, 0, 3-1); + free_dmatrix(sampSENS, 0, nasamp-1, 0, 7-1); + free_dmatrix(isampSENS, 0, 7-1, 0, nasamp-1); + + return inst_ok; +} + + +/* ------------------------------------------------------------ */ + +/* Read all the relevant register values */ +static inst_code +spyd2_read_all_regs( + spyd2 *p /* Object */ +) { + inst_code ev; + + a1logd(p->log, 3, "spyd2_read_all_regs: about to read all the EEProm values\n"); + + /* HW version */ + if ((ev = spyd2_rd_ee_uchar(p, &p->hwver, 5)) != inst_ok) + return ev; + + /* Feature bits */ + if ((ev = spyd2_rd_ee_uchar(p, &p->fbits, 6)) != inst_ok) + return ev; + + a1logd(p->log, 3, "spyd2_read_all_regs: hwver = 0x%02x%02x\n",p->hwver,p->fbits); + + /* Check the EEProm checksum */ + if (p->hwver == 7) { + if ((ev = spyd2_checkEECRC(p)) != inst_ok) + return ev; + } + + /* Serial number */ + if ((ev = spyd2_readEEProm(p, (unsigned char *)p->serno, 8, 8)) != inst_ok) + return ev; + p->serno[8] = '\000'; + a1logd(p->log, 3, "spyd2_read_all_regs: serno = '%s'\n",p->serno); + + if (p->hwver < 7) { + + /* Hmm. We deliberately ignore the fbits 0, 1 & 2 here, in case they are faulty */ + /* (Not sure if we should look at fbits 1 or not) */ + + /* Spyde2: CRT calibration values */ + /* Spyde3: Unknown calibration values */ + if ((ev = spyd2_rdreg_3x9xfloat(p, p->cal_A[0][0], p->cal_A[0][1], p->cal_A[0][2], 16)) + != inst_ok) + return ev; + if ((ev = spyd2_rdreg_3x9xfloat(p, p->cal_B[0][0], p->cal_B[0][1], p->cal_B[0][2], 128)) + != inst_ok) + return ev; + + + /* Hmm. The 0 table seems to sometimes be scaled. Is this a bug ? */ + /* (might be gain factor ?) */ + /* The spyder 3/4 doesn't use this anyway. */ + if (p->hwver >= 4) { + int j, k, i; + double avgmag = 0.0; + + for (i = j = 0; j < 3; j++) { + for (k = 0; k < 9; k++) { + if (p->cal_A[0][j][k] != 0.0) { + avgmag += fabs(p->cal_A[0][j][k]); + i++; + } + } + } + avgmag /= (double)(i); + a1logd(p->log, 4, "spyd2_read_all_regs: Cal_A avgmag = %f\n",avgmag); + + if (avgmag < 0.05) { + a1logd(p->log, 5, "spyd2_read_all_regs: Scaling Cal_A by 16\n"); + for (j = 0; j < 3; j++) { + for (k = 0; k < 9; k++) { + p->cal_A[0][j][k] *= 16.0; + } + } + } + } + + /* Spyder2: LCD calibration values */ + /* Spyder3: Normal CRT/LCD calibration values */ + if ((ev = spyd2_rdreg_3x9xfloat(p, p->cal_A[1][0], p->cal_A[1][1], p->cal_A[1][2], 256)) + != inst_ok) + return ev; + if ((ev = spyd2_rdreg_3x9xfloat(p, p->cal_B[1][0], p->cal_B[1][1], p->cal_B[1][2], 384)) + != inst_ok) + return ev; + + /* The monochrome "TOKIOBLUE" calibration */ + /* (Not sure if this is fbits 2 and 4 or not) */ + + /* Luminence only calibration values ??? */ + if ((ev = spyd2_rdreg_float(p, &p->cal_F[0], 240)) != inst_ok) + return ev; + if ((ev = spyd2_rdreg_float(p, &p->cal_F[1], 244)) != inst_ok) + return ev; + if ((ev = spyd2_rdreg_float(p, &p->cal_F[2], 248)) != inst_ok) + return ev; + if ((ev = spyd2_rdreg_float(p, &p->cal_F[3], 252)) != inst_ok) + return ev; + if ((ev = spyd2_rdreg_float(p, &p->cal_F[4], 364)) != inst_ok) + return ev; + if ((ev = spyd2_rdreg_float(p, &p->cal_F[5], 368)) != inst_ok) + return ev; + if ((ev = spyd2_rdreg_float(p, &p->cal_F[6], 372)) != inst_ok) + return ev; + + if (p->log->debug >= 4) { + int i, j, k; + + a1logd(p->log, 4, "Cal_A:\n"); + for (i = 0; i < 2;i++) { + for (j = 0; j < 3; j++) { + for (k = 0; k < 9; k++) { + a1logd(p->log, 4, "Cal_A [%d][%d][%d] = %f\n",i,j,k,p->cal_A[i][j][k]); + } + } + } + a1logd(p->log, 4, "\nCal_B:\n"); + for (i = 0; i < 2;i++) { + for (j = 0; j < 3; j++) { + for (k = 0; k < 9; k++) { + a1logd(p->log, 4, "Cal_B [%d][%d][%d] = %f\n",i,j,k,p->cal_B[i][j][k]); + } + } + } + a1logd(p->log, 4, "\nCal_F:\n"); + for (i = 0; i < 7;i++) { + a1logd(p->log, 4, "Cal_F [%d] = %f\n",i,p->cal_F[i]); + } + a1logd(p->log, 4, "\n"); + } + + } else if (p->hwver == 7) { + int i, j; + unsigned int sscal; + double tsens[7][41]; + + /* Read sensor sensitivity spectral data */ + if ((ev = spyd2_rdreg_7x41xshort(p, tsens, 170)) != inst_ok) + return ev; + + /* Sensor scale factor */ + if ((ev = spyd2_rd_ee_ushort(p, &sscal, 21)) != inst_ok) + return ev; + + /* And apply it to the sensor data */ + for (j = 0; j < 7; j++) { + for (i = 0; i < 41; i++) { + tsens[j][i] /= 1000; /* Convert to Hz per mW/nm/m^2 */ + tsens[j][i] /= sscal/1e5; /* Sensitivity scale value */ + } + } + + /* Convert sensor values to xspect's */ + for (i = 0; i < 7; i++) { + p->sens[i].spec_n = 41; + p->sens[i].spec_wl_short = 380; + p->sens[i].spec_wl_long = 780; + p->sens[i].norm = 1.0; + for (j = 0; j < 41; j++) { + p->sens[i].spec[j] = tsens[i][j]; + } + } +#ifdef SAVE_SPECTRA + write_nxspect("sensors.sp", p->sens, 7, 0); +#endif + + /* Linearization */ + if ((ev = spyd2_rdreg_3x9xfloat(p, p->cal_B[1][0], p->cal_B[1][1], p->cal_B[1][2], 60)) + != inst_ok) + return ev; + +#ifdef PLOT_SPECTRA + /* Plot the sensor spectra */ + { + int i, j; + double xx[81]; + double yy[10][81], *yp[10]; + + for (i = 0; i < 81; i++) + xx[i] = 380.0 + i * 5.0; + + for (j = 0; j < 7; j++) { + for (i = 0; i < 81; i++) + yy[j][i] = value_xspect(&p->sens[j], xx[i]); + yp[j] = yy[j]; + } + for (; j < 10; j++) + yp[j] = NULL; + + printf("The sensor and ambient sensor sensitivy curves\n"); + do_plot10(xx, yp[0], yp[1], yp[2], yp[3], yp[4], yp[5], yp[6], yp[7], yp[8], yp[9], 81, 0); + + + for (j = 0; j < spyd4_nocals; j++) { + double max = 0; + for (i = 0; i < 81; i++) { + if (yy[j][i] = value_xspect(&spyd4_cals[j], xx[i]) > max) + max = value_xspect(&spyd4_cals[j], xx[i]); + } + for (i = 0; i < 81; i++) + yy[j][i] = value_xspect(&spyd4_cals[j], xx[i])/max; + yp[j] = yy[j]; + } + for (; j < 10; j++) + yp[j] = NULL; + + printf("The display spectra\n"); + do_plot10(xx, yp[0], yp[1], yp[2], yp[3], yp[4], yp[5], yp[6], yp[7], yp[8], yp[9], 81, 0); + } +#endif /* PLOT_SPECTRA */ + + } + + a1logd(p->log, 3, "spyd2_read_all_regs: all EEProm read OK\n"); + + return inst_ok; +} + +/* ------------------------------------------------------------ */ + +/* Table to hold Spyder 2 Firmware, if it's installed */ +unsigned int _spyder2_pld_size = 0; /* Number of bytes to download */ +unsigned int *spyder2_pld_size = &_spyder2_pld_size; +unsigned char *spyder2_pld_bytes = NULL; + +/* Spyder 2: Download the PLD if it is available, and check status */ +static inst_code +spyd2_download_pld( + spyd2 *p /* Object */ +) { + inst_code ev; + int stat; + int i; + + a1logd(p->log, 2, "spyd2_download_pld: called\n"); + + if (*spyder2_pld_size == 0 || *spyder2_pld_size == 0x11223344) { + a1logd(p->log, 1, "spyd2_download_pld: No PLD pattern available! (have you run spyd2en ?)\n"); + return spyd2_interp_code((inst *)p, SPYD2_NO_PLD_PATTERN) ; + } + + for (i = 0; i < *spyder2_pld_size; i += 8) { + if ((ev = spyd2_loadPLD(p, spyder2_pld_bytes + i, 8)) != inst_ok) + return ev; + } + + /* Let the PLD initialize */ + msec_sleep(500); + +#ifdef DO_RESETEP /* Do the miscelanous resetep()'s */ + /* Reset the coms */ + p->icom->usb_resetep(p->icom, 0x81); + msec_sleep(1); /* Let device recover ? */ +#endif /* DO_RESETEP */ + + /* Check the status */ + if ((ev = spyd2_getstatus(p, &stat)) != inst_ok) + return ev; + + if (stat != 0) { + a1logd(p->log, 1, "spyd2_download_pld: PLD download failed!\n"); + return spyd2_interp_code((inst *)p, SPYD2_PLDLOAD_FAILED); + } + + a1logd(p->log, 2, "spyd2_download_pld: PLD download OK\n"); + + msec_sleep(500); +#ifdef DO_RESETEP /* Do the miscelanous resetep()'s */ + p->icom->usb_resetep(p->icom, 0x81); + msec_sleep(1); /* Let device recover ? */ +#endif /* DO_RESETEP */ + + return inst_ok; +} + + +/* ------------------------------------------------------------ */ +/* Setup Spyder4 native calibrations */ + +/* Load the manufacturers Spyder4 calibration data */ +/* Return a SPYD2_ error value */ +static int +spyd4_load_cal(spyd2 *p) { + char **bin_paths = NULL; + int no_paths = 0; + unsigned int size; + unsigned char *buf = NULL; + FILE *fp = NULL; + int nocals = 0; + int i, j; + + /* If already loaded */ + if (spyd4_nocals != 0) + return SPYD2_OK; + + + for (;;) { /* So we can break */ + if ((no_paths = xdg_bds(NULL, &bin_paths, xdg_data, xdg_read, xdg_user, + "ArgyllCMS/spyd4cal.bin" XDG_FUDGE "color/spyd4cal.bin" + )) < 1) + break; + + /* open binary file */ +#if !defined(O_CREAT) && !defined(_O_CREAT) +# error "Need to #include fcntl.h!" +#endif +#if defined(O_BINARY) || defined(_O_BINARY) + if ((fp = fopen(bin_paths[0],"rb")) == NULL) +#else + if ((fp = fopen(bin_paths[0],"r")) == NULL) +#endif + break; + xdg_free(bin_paths, no_paths); + + /* Figure out how big file it is */ + if (fseek(fp, 0, SEEK_END)) { + fclose(fp); + break; + } + size = (unsigned long)ftell(fp); + + if ((size % (41 * 8)) != 0) { + fclose(fp); + a1logd(p->log, 1, "spyd4_load_cal: calibration file '%s' is unexpected size\n",bin_paths[0]); + break; + } + + nocals = size/(41 * 8); + if (nocals != 6) { + fclose(fp); + a1logd(p->log, 1, "spyd4_load_cal: calibration file '%s' is unexpected number of calibrations (%d)\n",bin_paths[0],nocals); + break; + } + + if (fseek(fp, 0, SEEK_SET)) { + fclose(fp); + break; + } + + if ((buf = (unsigned char *)calloc(nocals * 41, 8)) == NULL) { + fclose(fp); + return SPYD2_MALLOC; + } + + if (fread(buf, 1, size, fp) != size) { + free(buf); + fclose(fp); + break; + } + fclose(fp); + break; + } + + if (buf == NULL) + nocals = 1; + + if ((spyd4_cals = (xspect *)calloc(nocals, sizeof(xspect))) == NULL) { + if (buf != NULL) + free(buf); + return SPYD2_MALLOC; + } + + /* If we have calibrations */ + if (buf != NULL) { + unsigned char *bp; + + for (i = 0; i < nocals; i++) { + bp = buf + 41 * 8 * i; + + spyd4_cals[i].spec_n = 41; + spyd4_cals[i].spec_wl_short = 380; + spyd4_cals[i].spec_wl_long = 780; + spyd4_cals[i].norm = 1.0; + + for (j = 0; j < 41; j++, bp += 8) { + ORD64 val; + + val = buf2ord64(bp); + spyd4_cals[i].spec[j] = IEEE754_64todouble(val); +// a1logd(p->log, 3, "cal[%d][%d] = %f\n",i,j,spyd4_cals[i].spec[j]); + } + } + + } else { + + /* Create a default calibration */ + for (j = 0; j < 41; j++) + spyd4_cals[0].spec_n = 41; + spyd4_cals[0].spec_wl_short = 380; + spyd4_cals[0].spec_wl_long = 780; + spyd4_cals[0].norm = 1.0; + + for (j = 0; j < 41; j++) { + spyd4_cals[0].spec[j] = 1.0; + } + } + + spyd4_nocals = nocals; + + return SPYD2_OK; +} + +/* ============================================================ */ + + +/* Establish communications with a SPYD2 */ +/* If it's a serial port, use the baud rate given, and timeout in to secs */ +/* Return DTP_COMS_FAIL on failure to establish communications */ +static inst_code +spyd2_init_coms(inst *pp, baud_rate br, flow_control fc, double tout) { + spyd2 *p = (spyd2 *) pp; + int se; + icomuflags usbflags = icomuf_none; + + a1logd(p->log, 2, "spyd2_init_coms: about to init coms\n"); + + if (p->icom->port_type(p->icom) != icomt_usb) { + a1logd(p->log, 1, "spyd2_init_coms: coms is not the right type!\n"); + return spyd2_interp_code((inst *)p, SPYD2_UNKNOWN_MODEL); + } + + a1logd(p->log, 2, "spyd2_init_coms: about to init USB\n"); + + /* On MSWindows the Spyder 3 doesn't work reliably unless each */ + /* read is preceeded by a reset endpoint. */ + /* (!!! This needs checking to see if it's still true. */ + /* Should switch back to libusb0.sys and re-test.) */ + /* (and Spyder 2 hangs if a reset ep is done on MSWin.) */ + /* The spyder 2 doesn't work well with the winusb driver either, */ + /* it needs icomuf_resetep_before_read to work at all, and */ + /* gets retries anyway. So we use the libusb0 driver for it. */ +#if defined(NT) + if (p->itype == instSpyder3) { + usbflags |= icomuf_resetep_before_read; /* The spyder USB is buggy ? */ + } +#endif + + /* On OS X the Spyder 2 can't close properly */ +#if defined(__APPLE__) /* OS X*/ + if (p->itype == instSpyder2) { + usbflags |= icomuf_reset_before_close; /* The spyder 2 USB is buggy ? */ + } +#endif + +#ifdef NEVER /* Don't want this now that we avoid 2nd set_config on Linux */ +#if defined(UNIX_X11) /* Linux*/ + /* On Linux the Spyder 2 doesn't work reliably unless each */ + /* read is preceeded by a reset endpoint. */ + if (p->itype == instSpyder2) { + usbflags |= icomuf_resetep_before_read; /* The spyder USB is buggy ? */ + } +#endif +#endif + + /* Set config, interface, write end point, read end point */ + /* ("serial" end points aren't used - the spyd2lay uses USB control messages) */ + if ((se = p->icom->set_usb_port(p->icom, 1, 0x00, 0x00, usbflags, 0, NULL)) != ICOM_OK) { + a1logd(p->log, 1, "spyd2_init_coms: failed ICOM err 0x%x\n",se); + return spyd2_interp_code((inst *)p, icoms2spyd2_err(se)); + } + + a1logd(p->log, 2, "spyd2_init_coms: suceeded\n"); + + p->gotcoms = 1; + return inst_ok; +} + +static inst_code set_default_disp_type(spyd2 *p); + +/* Initialise the SPYD2 */ +/* return non-zero on an error, with an inst_code */ +static inst_code +spyd2_init_inst(inst *pp) { + spyd2 *p = (spyd2 *)pp; + inst_code ev = inst_ok; + int stat; + int i; + + a1logd(p->log, 2, "spyd2_init_inst: called\n"); + + if (p->gotcoms == 0) /* Must establish coms before calling init */ + return spyd2_interp_code((inst *)p, SPYD2_NO_COMS); + + if (p->itype != instSpyder2 + && p->itype != instSpyder3 + && p->itype != instSpyder4) + return spyd2_interp_code((inst *)p, SPYD2_UNKNOWN_MODEL); + + p->refrate = DEFRRATE; + for (i = 0; i < 8; i++) + p->prevraw[i] = 0; /* Internal counters will be reset */ + p->prevrawinv = 0; /* prevraw is valid */ + + /* For Spyder 1 & 2, reset the hardware and wait for it to become ready. */ + if (p->itype != instSpyder3 + && p->itype != instSpyder4) { + + /* Reset the instrument */ + if ((ev = spyd2_reset(p)) != inst_ok) + return ev; + + /* Fetch status until we get a status = 1 */ + for (i = 0; i < 50; i++) { + if ((ev = spyd2_getstatus(p, &stat)) != inst_ok) + return ev; + + if (stat == 1) + break; + } + if (i >= 50) + return spyd2_interp_code((inst *)p, SPYD2_BADSTATUS); + + } else { + /* Because the Spyder 3/4 doesn't have a reset command, */ + /* it may be left in a borked state if the driver is aborted. */ + /* Make sure there's no old read data hanging around. */ + /* Sometimes it takes a little while for the old data to */ + /* turn up, so try at least for 1 second. */ + /* This won't always work if the driver is re-started */ + /* quickly after aborting a long integration read. */ + + unsigned char buf[8]; /* return bytes read */ + int rwbytes; /* Data bytes read or written */ + + + for (i = 0; i < 10; i++) { + if ((p->icom->usb_read(p->icom, NULL, 0x81, buf, 8, &rwbytes, 0.1) & ICOM_TO) + && i > 9) + break; /* Done when read times out */ + } + } + + /* Read the Serial EEProm contents */ + if ((ev = spyd2_read_all_regs(p)) != inst_ok) + return ev; + + /* Spyder 2 */ + if (p->hwver < 4) { + /* Download the PLD pattern and check the status */ + if ((ev = spyd2_download_pld(p)) != inst_ok) + return ev; + } + + p->gain = 1.0; + if (p->hwver == 5) { + if ((ev = spyd2_SetGain(p, 4)) != inst_ok) + return ev; + } + + /* Set a default calibration */ + if ((ev = set_default_disp_type(p)) != inst_ok) { + return ev; + } + + /* Do a dumy sensor read. This will set prevraw[] values. */ + { + int clocks = 500; + int minfclks = 0; + int maxfclks = 0; + msec_sleep(100); + if ((ev = spyd2_GetReading_ll(p, &clocks, 10, 0, &minfclks, &maxfclks, NULL, NULL, NULL)) != inst_ok) + return ev; + } + + p->trig = inst_opt_trig_user; /* default trigger mode */ + + p->inited = 1; + a1logd(p->log, 2, "spyd2_init_inst: inited OK\n"); + + if (p->hwver >= 4) { + /* Flash the LED, just cos we can! */ + if ((ev = spyd2_setLED(p, 2, 0.0)) != inst_ok) + return ev; + msec_sleep(200); + if ((ev = spyd2_setLED(p, 0, 0.0)) != inst_ok) + return ev; + } + + a1logv(p->log, 1, "Instrument Type: %s\n" + "Serial Number: %s\n" + "Hardware version: 0x%02x%02x\n" + ,inst_name(p->itype) ,p->serno ,p->hwver,p->fbits); + + return inst_ok; +} + +/* Read a single sample */ +/* Return the dtp error code */ +static inst_code +spyd2_read_sample( +inst *pp, +char *name, /* Strip name (7 chars) */ +ipatch *val, /* Pointer to instrument patch value */ +instClamping clamp) { /* NZ if clamp XYZ/Lab to be +ve */ + spyd2 *p = (spyd2 *)pp; + int user_trig = 0; + inst_code ev = inst_protocol_error; + + if (!p->gotcoms) + return inst_no_coms; + if (!p->inited) + return inst_no_init; + + if (p->trig == inst_opt_trig_user) { + + if (p->uicallback == NULL) { + a1logd(p->log, 1, "sptyd2: inst_opt_trig_user but no uicallback function set!\n"); + return inst_unsupported; + } + + for (;;) { + if ((ev = p->uicallback(p->uic_cntx, inst_armed)) != inst_ok) { + if (ev == inst_user_abort) + return ev; /* Abort */ + if (ev == inst_user_trig) { + user_trig = 1; + break; /* Trigger */ + } + } + msec_sleep(200); + } + /* Notify of trigger */ + if (p->uicallback) + p->uicallback(p->uic_cntx, inst_triggered); + + /* Progromatic Trigger */ + } else { + /* Check for abort */ + if (p->uicallback != NULL + && (ev = p->uicallback(p->uic_cntx, inst_armed)) == inst_user_trig) + return ev; /* Abort */ + } + + if (IMODETST(p->mode, inst_mode_emis_ambient)) { + if ((ev = spyd2_GetAmbientReading(p, val->XYZ)) != inst_ok) + return ev; + + } else { + + /* Attempt a CRT frame rate calibration if needed */ + if (p->refrmode != 0 && p->rrset == 0) { + if ((ev = spyd2_GetRefRate(p)) != inst_ok) + return ev; + } + + /* Read the XYZ value */ + if ((ev = spyd2_GetReading(p, val->XYZ)) != inst_ok) + return ev; + + /* Apply the colorimeter correction matrix */ + icmMulBy3x3(val->XYZ, p->ccmat, val->XYZ); + } + /* This may not change anything since instrument may clamp */ + if (clamp) + icmClamp3(val->XYZ, val->XYZ); + + val->loc[0] = '\000'; + if (IMODETST(p->mode, inst_mode_emis_ambient)) + val->mtype = inst_mrt_ambient; + else + val->mtype = inst_mrt_emission; + val->XYZ_v = 1; /* These are absolute XYZ readings ? */ + val->sp.spec_n = 0; + val->duration = 0.0; + + if (user_trig) + return inst_user_trig; + return ev; +} + +/* Insert a colorimetric correction matrix in the instrument XYZ readings */ +/* This is only valid for colorimetric instruments. */ +/* To remove the matrix, pass NULL for the filter filename */ +inst_code spyd2_col_cor_mat( +inst *pp, +double mtx[3][3] +) { + spyd2 *p = (spyd2 *)pp; + + if (!p->gotcoms) + return inst_no_coms; + if (!p->inited) + return inst_no_init; + + if (mtx == NULL) { + icmSetUnity3x3(p->ccmat); + } else { + if (p->cbid == 0) { + a1loge(p->log, 1, "spyd2: can't set col_cor_mat over non base display type\n"); + inst_wrong_setup; + } + icmCpy3x3(p->ccmat, mtx); + } + + return inst_ok; +} + +/* Use a Colorimeter Calibration Spectral Set to set the */ +/* instrumen calibration. */ +/* This is only valid for colorimetric instruments. */ +/* To set calibration back to default, pass NULL for sets. */ +inst_code spyd2_col_cal_spec_set( +inst *pp, +xspect *sets, +int no_sets +) { + spyd2 *p = (spyd2 *)pp; + inst_code ev = inst_ok; + + if (!p->gotcoms) + return inst_no_coms; + if (!p->inited) + return inst_no_init; + if (p->hwver < 7) + return inst_unsupported; + + if (sets == NULL || no_sets <= 0) { + if ((ev = set_default_disp_type(p)) != inst_ok) + return ev; + } else { + /* Use given spectral samples */ + if ((ev = spyd4_comp_calmat(p, p->obType, p->custObserver, sets, no_sets)) != inst_ok) + return ev; + p->icx = (99 << 1) | 1; /* Out of range index */ + } + return ev; +} + +/* Return needed and available inst_cal_type's */ +static inst_code spyd2_get_n_a_cals(inst *pp, inst_cal_type *pn_cals, inst_cal_type *pa_cals) { + spyd2 *p = (spyd2 *)pp; + + inst_cal_type n_cals = inst_calt_none; + inst_cal_type a_cals = inst_calt_none; + + if (p->refrmode != 0) { + if (p->rrset == 0) + n_cals |= inst_calt_ref_freq; + a_cals |= inst_calt_ref_freq; + } + + if (pn_cals != NULL) + *pn_cals = n_cals; + + if (pa_cals != NULL) + *pa_cals = a_cals; + + return inst_ok; +} + +/* Request an instrument calibration. */ +/* This is use if the user decides they want to do a calibration, */ +/* in anticipation of a calibration (needs_calibration()) to avoid */ +/* requiring one during measurement, or in response to measuring */ +/* returning inst_needs_cal. Initially us an inst_cal_cond of inst_calc_none, */ +/* and then be prepared to setup the right conditions, or ask the */ +/* user to do so, each time the error inst_cal_setup is returned. */ +inst_code spyd2_calibrate( +inst *pp, +inst_cal_type *calt, /* Calibration type to do/remaining */ +inst_cal_cond *calc, /* Current condition/desired condition */ +char id[CALIDLEN] /* Condition identifier (ie. white reference ID) */ +) { + spyd2 *p = (spyd2 *)pp; + inst_code ev = inst_ok; + inst_cal_type needed, available; + + if (!p->gotcoms) + return inst_no_coms; + if (!p->inited) + return inst_no_init; + + id[0] = '\000'; + + if ((ev = spyd2_get_n_a_cals((inst *)p, &needed, &available)) != inst_ok) + return ev; + + /* Translate inst_calt_all/needed into something specific */ + if (*calt == inst_calt_all + || *calt == inst_calt_needed + || *calt == inst_calt_available) { + if (*calt == inst_calt_all) + *calt = (needed & inst_calt_n_dfrble_mask) | inst_calt_ap_flag; + else if (*calt == inst_calt_needed) + *calt = needed & inst_calt_n_dfrble_mask; + else if (*calt == inst_calt_available) + *calt = available & inst_calt_n_dfrble_mask; + + a1logd(p->log,4,"spyd2_calibrate: doing calt 0x%x\n",calt); + + if ((*calt & inst_calt_n_dfrble_mask) == 0) /* Nothing todo */ + return inst_ok; + } + + if ((*calt & inst_calt_ref_freq) && p->refrmode != 0) { + + if (*calc != inst_calc_emis_white) { + *calc = inst_calc_emis_white; + return inst_cal_setup; + } + + /* Do CRT frame rate calibration */ + if ((ev = spyd2_GetRefRate(p)) != inst_ok) + return ev; + + *calt &= ~inst_calt_ref_freq; + } + + return inst_ok; +} + +/* Return the last calibrated refresh rate in Hz. Returns: */ +static inst_code spyd2_get_refr_rate(inst *pp, +double *ref_rate +) { + spyd2 *p = (spyd2 *)pp; + if (p->refrvalid) { + *ref_rate = p->refrate; + return inst_ok; + } else if (p->rrset) { + *ref_rate = 0.0; + return inst_misread; + } + return inst_needs_cal; +} + +/* Set the calibrated refresh rate in Hz. */ +/* Set refresh rate to 0.0 to mark it as invalid */ +/* Rates outside the range 5.0 to 150.0 Hz will return an error */ +static inst_code spyd2_set_refr_rate(inst *pp, +double ref_rate +) { + spyd2 *p = (spyd2 *)pp; + + if (ref_rate != 0.0 && (ref_rate < 5.0 || ref_rate > 150.0)) + return inst_bad_parameter; + + p->refrate = ref_rate; + if (ref_rate == 0.0) + p->refrate = DEFRRATE; + else + p->refrvalid = 1; + p->rrset = 1; + + return inst_ok; +} + +/* Error codes interpretation */ +static char * +spyd2_interp_error(inst *pp, int ec) { +// spyd2 *p = (spyd2 *)pp; + ec &= inst_imask; + switch (ec) { + case SPYD2_INTERNAL_ERROR: + return "Non-specific software internal software error"; + case SPYD2_COMS_FAIL: + return "Communications failure"; + case SPYD2_UNKNOWN_MODEL: + return "Not a Spyder 2 or 3"; + case SPYD2_DATA_PARSE_ERROR: + return "Data from i1 Display didn't parse as expected"; + + case SPYD2_OK: + return "No device error"; + + /* device specific errors */ + case SPYD2_BADSTATUS: + return "Too many retries waiting for status to come good"; + case SPYD2_PLDLOAD_FAILED: + return "Wrong status after download of PLD"; + case SPYD2_BADREADSIZE: + return "Didn't read expected amount of data"; + case SPYD2_TRIGTIMEOUT: + return "Trigger timout"; + case SPYD2_OVERALLTIMEOUT: + return "Overall timout"; + case SPYD2_BAD_EE_CRC: + return "Serial EEProm CRC failed"; + + /* Internal errors */ + case SPYD2_BAD_EE_ADDRESS: + return "Serial EEProm read is out of range"; + case SPYD2_BAD_EE_SIZE: + return "Serial EEProm read size > 256"; + case SPYD2_NO_PLD_PATTERN: + return "No PLD firmware pattern is available (have you run spyd2en ?)"; + case SPYD2_NO_COMS: + return "Communications hasn't been established"; + case SPYD2_NOT_INITED: + return "Insrument hasn't been initialised"; + case SPYD2_NOCRTCAL: + return "Insrument is missing the CRT calibration table"; + case SPYD2_NOLCDCAL: + return "Insrument is missing the Normal or LCD calibration table"; + case SPYD2_MALLOC: + return "Memory allocation failure"; + case SPYD2_OBS_SELECT: + return "Failed to set observer type"; + case SPYD2_CAL_FAIL: + return "Calibration calculation failed"; + case SPYD2_INT_CIECONVFAIL: + return "Creating spectral to CIE converted failed"; + case SPYD2_TOO_FEW_CALIBSAMP: + return "There are too few spectral calibration samples - need at least 3"; + + /* Configuration */ + case SPYD2_DISP_SEL_RANGE: + return "Display device selection out of range"; + + default: + return "Unknown error code"; + } +} + + +/* Convert a machine specific error code into an abstract dtp code */ +static inst_code +spyd2_interp_code(inst *pp, int ec) { +// spyd2 *p = (spyd2 *)pp; + + ec &= inst_imask; + switch (ec) { + + case SPYD2_OK: + return inst_ok; + + case SPYD2_INTERNAL_ERROR: + case SPYD2_NO_COMS: + case SPYD2_NOT_INITED: + case SPYD2_BAD_EE_ADDRESS: + case SPYD2_BAD_EE_SIZE: + case SPYD2_NO_PLD_PATTERN: + case SPYD2_MALLOC: + case SPYD2_OBS_SELECT: + case SPYD2_CAL_FAIL: + case SPYD2_INT_CIECONVFAIL: + case SPYD2_TOO_FEW_CALIBSAMP: + return inst_internal_error | ec; + + case SPYD2_COMS_FAIL: + case SPYD2_BADREADSIZE: + case SPYD2_TRIGTIMEOUT: + case SPYD2_BADSTATUS: + case SPYD2_OVERALLTIMEOUT: + return inst_coms_fail | ec; + + case SPYD2_UNKNOWN_MODEL: + return inst_unknown_model | ec; + +// return inst_protocol_error | ec; + + case SPYD2_NOCRTCAL: + case SPYD2_NOLCDCAL: + case SPYD2_PLDLOAD_FAILED: + case SPYD2_BAD_EE_CRC: + return inst_hardware_fail | ec; + + case SPYD2_DISP_SEL_RANGE: + return inst_wrong_setup | ec; + + } + return inst_other_error | ec; +} + +/* Destroy ourselves */ +static void +spyd2_del(inst *pp) { + spyd2 *p = (spyd2 *)pp; + if (p->icom != NULL) + p->icom->del(p->icom); + inst_del_disptype_list(p->dtlist, p->ndtlist); + free(p); +} + +/* Return the instrument mode capabilities */ +void spyd2_capabilities(inst *pp, +inst_mode *pcap1, +inst2_capability *pcap2, +inst3_capability *pcap3) { + spyd2 *p = (spyd2 *)pp; + inst_mode cap1= 0; + inst2_capability cap2 = 0; + + cap1 |= inst_mode_emis_spot + | inst_mode_emis_refresh_ovd + | inst_mode_emis_norefresh_ovd + | inst_mode_colorimeter + ; + + /* We don't seem to have a way of detecting the lack */ + /* of ambinent capability, short of doing a read */ + /* and noticing the result is zero. */ + if (p->itype == instSpyder3 + || p->itype == instSpyder4) { + cap1 |= inst_mode_emis_ambient; + } + + cap2 |= inst2_prog_trig + | inst2_user_trig + | inst2_ccmx + | inst2_refresh_rate + | inst2_emis_refr_meas + ; + + if (p->itype == instSpyder3 + || p->itype == instSpyder4) { + cap2 |= inst2_disptype; + cap2 |= inst2_has_leds; + cap2 |= inst2_ambient_mono; + } else { + cap2 |= inst2_disptype; + } + + if (p->itype == instSpyder4) + cap2 |= inst2_ccss; /* Spyder4 has spectral sensiivities */ + + if (pcap1 != NULL) + *pcap1 = cap1; + if (pcap2 != NULL) + *pcap2 = cap2; + if (pcap3 != NULL) + *pcap3 = inst3_none; +} + +/* Check device measurement mode */ +inst_code spyd2_check_mode(inst *pp, inst_mode m) { + spyd2 *p = (spyd2 *)pp; + inst_mode cap; + + if (!p->gotcoms) + return inst_no_coms; + if (!p->inited) + return inst_no_init; + + pp->capabilities(pp, &cap, NULL, NULL); + + /* Simple test */ + if (m & ~cap) + return inst_unsupported; + + if (!IMODETST(m, inst_mode_emis_spot) + && !IMODETST(m, inst_mode_emis_ambient)) { + return inst_unsupported; + } + + return inst_ok; +} + +/* Set device measurement mode */ +inst_code spyd2_set_mode(inst *pp, inst_mode m) { + spyd2 *p = (spyd2 *)pp; + inst_code ev; + + if ((ev = spyd2_check_mode(pp, m)) != inst_ok) + return ev; + + p->mode = m; + + if ( IMODETST(p->mode, inst_mode_emis_norefresh_ovd)) /* Must test this first! */ + p->refrmode = 0; + else if (IMODETST(p->mode, inst_mode_emis_refresh_ovd)) + p->refrmode = 1; + + return inst_ok; +} + +inst_disptypesel spyd2_disptypesel[3] = { + { + inst_dtflags_default, + 1, + "l", + "LCD display", + 0, + 1 + }, + { + inst_dtflags_none, /* flags */ + 2, /* cbid */ + "c", /* sel */ + "CRT display", /* desc */ + 1, /* refr */ + 0 /* ix */ + }, + { + inst_dtflags_end, + 0, + "", + "", + 0, + 0 + } +}; + +inst_disptypesel spyd3_disptypesel[3] = { + { + inst_dtflags_default, + 1, + "nl", + "Non-Refresh display", + 0, + 1 + }, + { + inst_dtflags_none, /* flags */ + 2, /* cbid */ + "rc", /* sel */ + "Refresh display", /* desc */ + 1, /* refr */ + 1 /* ix */ + }, + { + inst_dtflags_end, + 0, + "", + "", + 0, + 0 + } +}; + +inst_disptypesel spyd4_disptypesel_1[8] = { + { + inst_dtflags_default, + 1, + "nl", + "Generic Non-Refresh Display", + 0, + 1 + }, + { + inst_dtflags_none, /* flags */ + 2, /* cbid */ + "rc", /* sel */ + "Generic Refresh Display", /* desc */ + 1, /* refr */ + 1 /* ix */ + }, + { + inst_dtflags_end, + 0, + "", + "", + 0, + 0 + } +}; + +inst_disptypesel spyd4_disptypesel[8] = { + { + inst_dtflags_default, + 1, + "n", + "Generic Non-Refresh Display", + 0, + 1 + }, + { + inst_dtflags_none, /* flags */ + 2, /* cbid */ + "r", /* sel */ + "Generic Refresh Display", /* desc */ + 1, /* refr */ + 1 /* ix = hw bit + spec table << 1 */ + }, + { + inst_dtflags_none, /* flags */ + 0, + "f", + "LCD, CCFL Backlight", + 0, + (1 << 1) | 1 + }, + { + inst_dtflags_none, /* flags */ + 0, + "L", + "Wide Gamut LCD, CCFL Backlight", + 0, + (2 << 1) | 1 + }, + { + inst_dtflags_none, /* flags */ + 0, + "e", + "LCD, White LED Backlight", + 0, + (3 << 1) | 1 + }, + { + inst_dtflags_none, /* flags */ + 0, + "B", + "Wide Gamut LCD, RGB LED Backlight", + 0, + (4 << 1) | 1 + }, + { + inst_dtflags_none, /* flags */ + 0, + "x", + "LCD, CCFL Backlight (Laptop ?)", + 0, + (5 << 1) | 1 + }, + { + inst_dtflags_end, + 0, + "", + "", + 0, + 0 + } +}; + +static void set_base_disptype_list(spyd2 *p) { + /* set the base display type list */ + if (p->itype == instSpyder4) { + if (spyd4_nocals <= 1) { + p->_dtlist = spyd4_disptypesel_1; + } else { + p->_dtlist = spyd4_disptypesel; + } + } else if (p->itype == instSpyder3) { + p->_dtlist = spyd3_disptypesel; + } else { + p->_dtlist = spyd2_disptypesel; + } +} + +/* Get mode and option details */ +static inst_code spyd2_get_disptypesel( +inst *pp, +int *pnsels, /* Return number of display types */ +inst_disptypesel **psels, /* Return the array of display types */ +int allconfig, /* nz to return list for all configs, not just current. */ +int recreate /* nz to re-check for new ccmx & ccss files */ +) { + spyd2 *p = (spyd2 *)pp; + inst_code rv = inst_ok; + + /* Create/Re-create a current list of abailable display types */ + if (p->dtlist == NULL || recreate) { + if ((rv = inst_creat_disptype_list(pp, &p->ndtlist, &p->dtlist, + p->_dtlist, p->hwver >= 7 ? 1 : 0 /* doccss*/, 1 /* doccmx */)) != inst_ok) + return rv; + } + + if (pnsels != NULL) + *pnsels = p->ndtlist; + + if (psels != NULL) + *psels = p->dtlist; + + return inst_ok; +} + +/* Given a display type entry, setup for that type */ +static inst_code set_disp_type(spyd2 *p, inst_disptypesel *dentry) { + inst_code ev; + int refrmode; + + p->icx = dentry->ix; + p->cbid = dentry->cbid; + refrmode = dentry->refr; + + if ( IMODETST(p->mode, inst_mode_emis_norefresh_ovd)) { /* Must test this first! */ + refrmode = 0; + } else if (IMODETST(p->mode, inst_mode_emis_refresh_ovd)) { + refrmode = 1; + } + + if (p->refrmode != refrmode) { + p->rrset = 0; /* This is a hint we may have swapped displays */ + p->refrvalid = 0; + } + p->refrmode = refrmode; + + if (dentry->flags & inst_dtflags_ccss) { + + if ((ev = spyd4_comp_calmat(p, p->obType, p->custObserver, dentry->sets, dentry->no_sets)) + != inst_ok) { + a1logd(p->log, 1, "spyd4_set_disp_type: comp_calmat ccss failed with rv = 0x%x\n",ev); + return ev; + } + p->icx = (99 << 1) | 1; /* Out of range index */ + icmSetUnity3x3(p->ccmat); + + } else { + + if (p->hwver >= 7) { + if ((p->icx >> 1) > spyd4_nocals) + return inst_unsupported; + + /* Create the calibration matrix */ + if ((ev = spyd4_set_cal(p, p->icx >> 1)) != inst_ok) + return ev; + } + + if (dentry->flags & inst_dtflags_ccmx) { + icmCpy3x3(p->ccmat, dentry->mat); + } else { + icmSetUnity3x3(p->ccmat); + } + } + + return inst_ok; +} + + +/* Setup the default display type */ +static inst_code set_default_disp_type(spyd2 *p) { + inst_code ev; + int i; + + if (p->dtlist == NULL) { + if ((ev = inst_creat_disptype_list((inst *)p, &p->ndtlist, &p->dtlist, + p->_dtlist, p->hwver >= 7 ? 1 : 0 /* doccss*/, 1 /* doccmx */)) != inst_ok) + return ev; + } + + for (i = 0; !(p->dtlist[i].flags & inst_dtflags_end); i++) { + if (p->dtlist[i].flags & inst_dtflags_default) + break; + } + if (p->dtlist[i].flags & inst_dtflags_end) { + a1loge(p->log, 1, "set_default_disp_type: failed to find type!\n"); + return inst_internal_error; + } + if ((ev = set_disp_type(p, &p->dtlist[i])) != inst_ok) { + return ev; + } + + return inst_ok; +} + +/* Set the display type */ +static inst_code spyd2_set_disptype(inst *pp, int ix) { + spyd2 *p = (spyd2 *)pp; + inst_code ev; + inst_disptypesel *dentry; + + if (!p->gotcoms) + return inst_no_coms; + if (!p->inited) + return inst_no_init; + + if (p->dtlist == NULL) { + if ((ev = inst_creat_disptype_list(pp, &p->ndtlist, &p->dtlist, + p->_dtlist, p->hwver >= 7 ? 1 : 0 /* doccss*/, 1 /* doccmx */)) != inst_ok) + return ev; + } + + if (ix < 0 || ix >= p->ndtlist) + return inst_unsupported; + + dentry = &p->dtlist[ix]; + + if ((ev = set_disp_type(p, dentry)) != inst_ok) { + return ev; + } + + return inst_ok; +} + +/* + * set or reset an optional mode + * + * Some options talk to the instrument, and these will + * error if it hasn't been initialised. + * [We could fix this by setting a flag and adding + * some extra logic in init()] + */ +static inst_code +spyd2_get_set_opt(inst *pp, inst_opt_type m, ...) { + spyd2 *p = (spyd2 *)pp; + inst_code ev = inst_ok; + + /* Record the trigger mode */ + if (m == inst_opt_trig_prog + || m == inst_opt_trig_user) { + p->trig = m; + return inst_ok; + } + + if (!p->gotcoms) + return inst_no_coms; + if (!p->inited) + return inst_no_init; + + /* Get the display type information */ + if (m == inst_opt_get_dtinfo) { + va_list args; + int *refrmode, *cbid; + + va_start(args, m); + refrmode = va_arg(args, int *); + cbid = va_arg(args, int *); + va_end(args); + + if (refrmode != NULL) + *refrmode = p->refrmode; + if (cbid != NULL) + *cbid = p->cbid; + + return inst_ok; + } + + /* Set the ccss observer type */ + if (m == inst_opt_set_ccss_obs) { + va_list args; + icxObserverType obType; + xspect *custObserver; + + va_start(args, m); + obType = va_arg(args, icxObserverType); + custObserver = va_arg(args, xspect *); + va_end(args); + + if (obType == icxOT_default) + obType = icxOT_CIE_1931_2; + p->obType = obType; + if (obType == icxOT_custom) { + p->custObserver[0] = custObserver[0]; + p->custObserver[1] = custObserver[1]; + p->custObserver[2] = custObserver[2]; + } + + return inst_ok; + } + + /* Operate the LED */ + if (p->hwver >= 4) { + if (m == inst_opt_get_gen_ledmask) { + va_list args; + int *mask = NULL; + + va_start(args, m); + mask = va_arg(args, int *); + va_end(args); + *mask = 0x1; /* One general LED */ + return inst_ok; + } else if (m == inst_opt_get_led_state) { + va_list args; + int *mask = NULL; + + va_start(args, m); + mask = va_arg(args, int *); + va_end(args); + *mask = p->led_state; + return inst_ok; + } else if (m == inst_opt_set_led_state) { + va_list args; + int mask = 0; + + va_start(args, m); + mask = 1 & va_arg(args, int); + va_end(args); + if ((ev = spyd2_setLED(p, mask & 1 ? 2 : 0, 0.0)) == inst_ok) { + p->led_state = mask; + } + return ev; + } + } + + if (m == inst_opt_get_pulse_ledmask) { + va_list args; + int *mask = NULL; + + va_start(args, m); + mask = va_arg(args, int *); + va_end(args); + *mask = 0x1; /* General LED is pulsable */ + return inst_ok; + } else if (m == inst_opt_set_led_pulse_state) { + va_list args; + double period, on_time_prop, trans_time_prop; + int mode; + + va_start(args, m); + period = va_arg(args, double); + on_time_prop = va_arg(args, double); + trans_time_prop = va_arg(args, double); + va_end(args); + if (period < 0.0 + || on_time_prop < 0.0 || on_time_prop > 1.0 + || trans_time_prop < 0.0 || trans_time_prop > 1.0 + || trans_time_prop > on_time_prop || trans_time_prop > (1.0 - on_time_prop)) + return inst_bad_parameter; + if (period == 0.0 || on_time_prop == 0.0) { + period = 0.0; + mode = 0; + p->led_state = 0; + } else { + mode = 1; + p->led_state = 1; + } + p->led_period = period; + p->led_on_time_prop = on_time_prop; + p->led_trans_time_prop = trans_time_prop; + return spyd2_setLED(p, mode, period); + } else if (m == inst_opt_get_led_state) { + va_list args; + double *period, *on_time_prop, *trans_time_prop; + + va_start(args, m); + period = va_arg(args, double *); + on_time_prop = va_arg(args, double *); + trans_time_prop = va_arg(args, double *); + va_end(args); + if (period != NULL) *period = p->led_period; + if (on_time_prop != NULL) *on_time_prop = p->led_on_time_prop; + if (trans_time_prop != NULL) *trans_time_prop = p->led_trans_time_prop; + return inst_ok; + } + return inst_unsupported; +} + +/* Constructor */ +extern spyd2 *new_spyd2(icoms *icom, instType itype) { + spyd2 *p; + if ((p = (spyd2 *)calloc(sizeof(spyd2),1)) == NULL) { + a1loge(icom->log, 1, "new_spyd2: malloc failed!\n"); + return NULL; + } + + p->log = new_a1log_d(icom->log); + + p->init_coms = spyd2_init_coms; + p->init_inst = spyd2_init_inst; + p->capabilities = spyd2_capabilities; + p->check_mode = spyd2_check_mode; + p->set_mode = spyd2_set_mode; + p->get_disptypesel = spyd2_get_disptypesel; + p->set_disptype = spyd2_set_disptype; + p->get_set_opt = spyd2_get_set_opt; + p->read_sample = spyd2_read_sample; + p->read_refrate = spyd2_read_refrate; + p->get_n_a_cals = spyd2_get_n_a_cals; + p->calibrate = spyd2_calibrate; + p->col_cor_mat = spyd2_col_cor_mat; + p->col_cal_spec_set = spyd2_col_cal_spec_set; + p->get_refr_rate = spyd2_get_refr_rate; + p->set_refr_rate = spyd2_set_refr_rate; + p->interp_error = spyd2_interp_error; + p->del = spyd2_del; + + p->icom = icom; + p->itype = icom->itype; + + /* Load manufacturers Spyder4 calibrations */ + if (itype == instSpyder4) { + int rv; + p->hwver = 7; /* Set preliminary version */ + if ((rv = spyd4_load_cal(p)) != SPYD2_OK) + a1logd(p->log, 1, "Loading Spyder4 calibrations failed with '%s'\n",p->interp_error((inst *)p, rv)); + if (spyd4_nocals < 1) + a1logd(p->log, 1, "Spyder4 choice of calibrations not available\n"); + } + if (itype == instSpyder3) { + p->hwver = 4; /* Set preliminary version */ + } + if (itype == instSpyder2) { + p->hwver = 3; /* Set preliminary version */ + } + + icmSetUnity3x3(p->ccmat); /* Set the colorimeter correction matrix to do nothing */ + set_base_disptype_list(p); + + return p; +} + -- cgit v1.2.3