diff options
Diffstat (limited to 'doc')
| -rw-r--r-- | doc/Makefile.in | 2 | ||||
| -rw-r--r-- | doc/ipmitool.1 | 288 |
2 files changed, 290 insertions, 0 deletions
diff --git a/doc/Makefile.in b/doc/Makefile.in index fec28ea..fb184ec 100644 --- a/doc/Makefile.in +++ b/doc/Makefile.in @@ -223,6 +223,8 @@ INTF_OPEN = @INTF_OPEN@ INTF_OPEN_LIB = @INTF_OPEN_LIB@ INTF_SERIAL = @INTF_SERIAL@ INTF_SERIAL_LIB = @INTF_SERIAL_LIB@ +INTF_USB = @INTF_USB@ +INTF_USB_LIB = @INTF_USB_LIB@ IPMITOOL_INTF_LIB = @IPMITOOL_INTF_LIB@ LD = @LD@ LDFLAGS = @LDFLAGS@ diff --git a/doc/ipmitool.1 b/doc/ipmitool.1 index 2c20821..10ccb74 100644 --- a/doc/ipmitool.1 +++ b/doc/ipmitool.1 @@ -291,6 +291,7 @@ Commands: kontronoem Manage Kontron OEM Extensions lan Configure LAN Channels mc Management Controller status and global enables + nm Node Manager pef Configure Platform Event Filtering (PEF) picmg Run a PICMG/ATA extended command power Shortcut to chassis power commands @@ -1921,6 +1922,27 @@ ADMIN, issue the following command: > ipmitool \-I \fIinterface\fR lan set \fIchannel\fR cipher_privs uaXXXXXXXXXXXXX +.TP + +\fIbad_pass_thresh\fP <\fBthresh_num\fR> <\fB1|0\fR> <\fBreset_interval\fR> <\fBlockout_interval\fR> +.br + +Sets the Bad Password Threshold. + +<\fBthresh_num\fR> If non-zero, this value determines the number of sequential bad passwords +that will be allowed to be entered for the identified user before the user is automatically +disabled from access on the channel. + +<\fB1|0\fR> 1 = generate a Session Audit sensor "Invalid password disable" event message. +0 = do not generate an event message when the user is disabled. + +<\fBreset_interval\fR> Attempt Count Reset Interval. The interval, in tens of seconds, for +which the accumulated count of bad password attempts is retained before being automatically +reset to zero. + +<\fBlockout_interval\fR> User Lockout Interval. The interval, in tens of seconds, that the user +will remain disabled after being disabled because the Bad Password Threshold number was reached. + .RE .TP \fIalert\fP \fIprint\fP [<\fBchannel\fR>] [<\fBalert destination\fR>] @@ -2382,6 +2404,272 @@ Clear valid bit on power up via power push button or wake event .RE .RE .RE +.TP +\fInm\fP +.RS +.TP +\fIalert\fP +.RS +.TP +\fIclear dest\fP <\fBdest\fR> +.br + +Clear the Node Manager Alert lan destination. + +.RE +.RS +.TP +\fIget\fP +.br +Get the Node Manager Alert settings. + +.RE +.RS +.TP +\fIset chan\fP <\fBchan\fR> \fIdest\fP <\fBdest\fR> \fIstring\fP <\fBstring\fR> +.br + +Set the Node Manager alert channel, lan destination, and alert string number. + +.RE +.TP +\fIcapability\fP +.br + +Obtain the Node Manager power control capabilities and ranges. + +.TP +\fIcontrol\fP +.RS +.TP +\fIenable\fP|\fIdisable \fP +.RS +.TP +\fIglobal\fP +.br + +Enable/disable all policies for all domains. +.TP +\fIper_domain\fP <platform|CPU|Memory> +.br + +Enable/disable all policies of the specified domain. +.TP +\fIper_policy\fP <0-7> +.br + +Enable/disable the policy for the specified domain/policy combination. +.RE +.RE +.TP +\fIdiscover\fP +.br + +Discover Node Manager presence as well as the Node Manager version, revision, and patch number. + +.TP +\fIpolicy\fP +.RS +.TP +\fIadd\fP +.RS +.TP +\fIpower\fP <watts> \fIpolicy_id\fP <0-7> [\fIcorrection\fP auto|soft|hard] \fItrig_lim\fP <seconds> \fIstats\fP <seconds> [\fIdomain\fP <platform|CPU|Memory>] \fIenable\fP|\fIdisable\fP +.br + +Add a new power policy, or overwrite an existing policy. +The \fIcorrection\fP parameter is the agressiveness of frequency limiting, default is auto. +The \fItrig_lim\fP is the correction time limit and must be at least 6000 and not greater than 65535. +The \fIstats\fP setting is the averaging period in seconds and ranges from 1-65535. +If domain is not supplied a default of platform is used. + + +.TP +\fIinlet\fP <temp> \fIpolicy_id\fP <0-7> [\fIcorrection\fP auto|soft|hard] \fItrig_lim\fP <seconds> \fIstats\fP <seconds> [\fIdomain\fP <platform|CPU|Memory>] \fIenable\fP|\fIdisable\fP +.br + +Add a new inlet temp policy, or overwrite an existing policy. +The \fIcorrection\fP parameter is the agressiveness of frequency limiting, default is auto. +The \fItrig_lim\fP is the correction time limit and must be at least 6000 and not greater than 65535. +The \fIstats\fP setting is the averaging period in seconds and ranges from 1-65535. +If domain is not supplied a default of platform is used. + + +.RE +.TP +\fIget\fP \fIpolicy_id\fP <0-7> +.br + +Get a previously stored policy. +.TP +\fIlimiting\fP +.br + +Report policy number if any policy is limiting power. +.TP +\fIremove\fP \fIpolicy_id\fP <0-7> [\fIdomain\fP <platform|CPU|Memory>] +.br + +Remove a policy. If domain is not supplied a default of platform is used. +.RE +.TP +\fIpower\fP \fImin\fP <minimum> \fImax\fP <maximum> [\fIdomain\fP <platform|CPU|Memory>] +.br + +Configure Node Manager power minumum and maximum power draw limits. +The \fImin\fP and \fImax\fP values must be in the range of 0-65535. +If domain is not supplied a default of platform is used. + +.RE +.RS +.TP +\fIreset\fP +.RS +.TP +\fIcomm\fP \fIpolicy_id\fP <0-7> [\fIdomain\fP <platform|CPU|Memory>] +.br + +Reset Node Manager communication statistics. +If domain is not supplied a default of platform is used. + +.TP +\fIglobal\fI +.br + +Reset Node Manager global statistics. + +.TP +\fImemory\fP \fIpolicy_id\fP <0-7> [\fIdomain\fP <platform|CPU|Memory>] +.br + +Reset Node Manager memory throttling statistics. +If domain is not supplied a default of platform is used. + +.TP +\fIper_policy\fP \fIpolicy_id\fP <0-7> [\fIdomain\fP <platform|CPU|Memory>] +.br + +Reset Node Manager per policy statistics. +If domain is not supplied a default of platform is used. + +.TP +\fIrequests\fP \fIpolicy_id\fP <0-7> [\fIdomain\fP <platform|CPU|Memory>] +.br + +Reset Node Manager unhandled requests statistics. +If domain is not supplied a default of platform is used. + +.TP +\fIresponse\fP \fIpolicy_id\fP <0-7> [\fIdomain\fP <platform|CPU|Memory>] +.br + +Reset Node Manager response time statistics. +If domain is not supplied a default of platform is used. + +.TP +\fIthrottling\fP \fIpolicy_id\fP <0-7> [\fIdomain\fP <platform|CPU|Memory>] +.br + +Reset Node Manager throttling statistics. +If domain is not supplied a default of platform is used. + +.RE +.TP +\fIstatistics\fP +.RS +.TP +\fIcomm_fail\fP +.br + +Report Node Manager communication failure statistics. + +.TP +\fIcpu_throttling\fP +.br + +Report Node Manager cpu throttling statistics. + +.TP +\fImem_throttling\fP +.br + +Report Node Manager memory throttling statistics. + +.TP +\fIpolicy_power\fP \fIpolicy_id\fP <0-7> [\fIdomain\fP <platform|CPU|Memory>] +.br + +Report Node Manager per policy power statistics (policy must be a power limit type policy). +If domain is not supplied a default of platform is used. + +.TP +\fIpolicy_temps\fP \fIpolicy_id\fP <0-7> [\fIdomain\fP <platform|CPU|Memory>] +.br + +Report Node Manager per policy temp statistics (policy must be an inlet temp limit policy). +If domain is not supplied a default of platform is used. + +.TP +\fIpolicy_throt\fP \fIpolicy_id\fP <0-7> [\fIdomain\fP <platform|CPU|Memory>] +.br + +Report Node Manager per policy throttling statistics. +If domain is not supplied a default of platform is used. + +.TP +\fIrequests\fP +.br + +Report Node Manager unhandled requests statistics. + +.TP +\fIresponse\fP +.br + +Report Node Manager response time statistics. + +.RE +.TP +\fIsuspend\fP +.RS +.TP +\fIget\fP \fIpolicy_id\fP <0-7> [\fIdomain\fP <platform|CPU|Memory>] +.br + +Get Node Manager policy suspend periods. +If domain is not supplied a default of platform is used. + +.TP +\fIset\fP \fIpolicy_id\fP <0-7> [\fIdomain\fP <platform|CPU|Memory>] <start> <stop> <repeat> +.br + +Set Node Manager policy suspend periods. +If domain is not supplied a default of platform is used. +The <start> and <stop> values must be in the range of 0-239, which is the number of minutes past midnight divided by 6. +The <repeat> value is the daily recurrence pattern. Bit 0 is repeat every Monday, bit 1 is repeat every Tuesday, on through bit 6 for Sunday. + +.RE +.TP +\fIthreshold\fP +.RS +.TP +\fIget\fP \fIpolicy_id\fP <0-7> [\fIdomain\fP <platform|CPU|Memory>] +.br + +Get Node Manager policy Alert Threshold settings. +If domain is not supplied a default of platform is used. + +.TP +\fIset\fP \fIpolicy_id\fP <0-7> [\fIdomain\fP <platform|CPU|Memory>] \fIthresh_array\fP +.br + +Set Node Manager policy Alert Threshold values. +If domain is not supplied a default of platform is used. +The \fIthresh_array\fP is 1, 2, or 3 integers that set three alert threshold settings. The setting type is a power or temperature value which must match the type of policy. + +.RE +.RE + .TP \fIpef\fP .RS |