From 1079962e4c06f88a54e50d997c1b7e84303d30b4 Mon Sep 17 00:00:00 2001 From: Bernhard Schmidt Date: Sat, 15 Aug 2020 21:29:50 +0200 Subject: New upstream version 2.5~beta1 --- doc/man-sections/vpn-network-options.rst | 534 +++++++++++++++++++++++++++++++ 1 file changed, 534 insertions(+) create mode 100644 doc/man-sections/vpn-network-options.rst (limited to 'doc/man-sections/vpn-network-options.rst') diff --git a/doc/man-sections/vpn-network-options.rst b/doc/man-sections/vpn-network-options.rst new file mode 100644 index 0000000..7100c1a --- /dev/null +++ b/doc/man-sections/vpn-network-options.rst @@ -0,0 +1,534 @@ +Virtual Network Adapter (VPN interface) +--------------------------------------- + +Options in this section relates to configuration of the virtual tun/tap +network interface, including setting the VPN IP address and network +routing. + +--bind-dev device + (Linux only) Set ``device`` to bind the server socket to a + `Virtual Routing and Forwarding`_ device + +--block-ipv6 + On the client, instead of sending IPv6 packets over the VPN tunnel, all + IPv6 packets are answered with an ICMPv6 no route host message. On the + server, all IPv6 packets from clients are answered with an ICMPv6 no + route to host message. This options is intended for cases when IPv6 + should be blocked and other options are not available. ``--block-ipv6`` + will use the remote IPv6 as source address of the ICMPv6 packets if set, + otherwise will use :code:`fe80::7` as source address. + + For this option to make sense you actually have to route traffic to the + tun interface. The following example config block would send all IPv6 + traffic to OpenVPN and answer all requests with no route to host, + effectively blocking IPv6. + + **Client config** + :: + + --ifconfig-ipv6 fd15:53b6:dead::2/64 fd15:53b6:dead::1 + --redirect-gateway ipv6 + --block-ipv6 + + **Server config** + Push a "valid" ipv6 config to the client and block on the server + :: + + --push "ifconfig-ipv6 fd15:53b6:dead::2/64 fd15:53b6:dead::1" + --push "redirect-gateway ipv6" + --block-ipv6 + +--dev device + TUN/TAP virtual network device which can be :code:`tunX`, :code:`tapX`, + :code:`null` or an arbitrary name string (:code:`X` can be omitted for + a dynamic device.) + + See examples section below for an example on setting up a TUN device. + + You must use either tun devices on both ends of the connection or tap + devices on both ends. You cannot mix them, as they represent different + underlying network layers: + + :code:`tun` + devices encapsulate IPv4 or IPv6 (OSI Layer 3) + + :code:`tap` + devices encapsulate Ethernet 802.3 (OSI Layer 2). + + Valid syntaxes: + :: + + dev tun2 + dev tap4 + dev ovpn + + When the device name starts with :code:`tun` or :code:`tap`, the device + type is extracted automatically. Otherwise the ``--dev-type`` option + needs to be added as well. + +--dev-node node + Explicitly set the device node rather than using :code:`/dev/net/tun`, + :code:`/dev/tun`, :code:`/dev/tap`, etc. If OpenVPN cannot figure out + whether ``node`` is a TUN or TAP device based on the name, you should + also specify ``--dev-type tun`` or ``--dev-type tap``. + + Under Mac OS X this option can be used to specify the default tun + implementation. Using ``--dev-node utun`` forces usage of the native + Darwin tun kernel support. Use ``--dev-node utunN`` to select a specific + utun instance. To force using the :code:`tun.kext` (:code:`/dev/tunX`) + use ``--dev-node tun``. When not specifying a ``--dev-node`` option + openvpn will first try to open utun, and fall back to tun.kext. + + On Windows systems, select the TAP-Win32 adapter which is named ``node`` + in the Network Connections Control Panel or the raw GUID of the adapter + enclosed by braces. The ``--show-adapters`` option under Windows can + also be used to enumerate all available TAP-Win32 adapters and will show + both the network connections control panel name and the GUID for each + TAP-Win32 adapter. + +--dev-type device-type + Which device type are we using? ``device-type`` should be :code:`tun` + (OSI Layer 3) or :code:`tap` (OSI Layer 2). Use this option only if + the TUN/TAP device used with ``--dev`` does not begin with :code:`tun` + or :code:`tap`. + +--dhcp-option args + Set additional network settings via DHCP. On Windows, this is parsed by + the ``tap-windows6`` or ``wintun`` driver. On other platforms these + options can be picked up by an ``--up`` script or plug-in if it has been + pushed by the OpenVPN server. The option will then be saved in the + client's environment before the ``--up`` script is called, under the name + :code:`foreign_option_{n}`. + + Valid syntax: + :: + + dhcp-options type [parm] + + :code:`DOMAIN` ``name`` + Set Connection-specific DNS Suffix to :code:`name`. + + :code:`DNS` ``address`` + Set primary domain name server IPv4 or IPv6 address. + Repeat this option to set secondary DNS server addresses. + + Note: DNS IPv6 servers are currently set using netsh (the existing + DHCP code can only do IPv4 DHCP, and that protocol only permits + IPv4 addresses anywhere). The option will be put into the + environment, so an ``--up`` script could act upon it if needed. + + :code:`WINS` ``address`` + Set primary WINS server address (NetBIOS over TCP/IP Name Server). + Repeat this option to set secondary WINS server addresses. + + :code:`NBDD` ``address`` + Set primary NBDD server address (NetBIOS over TCP/IP Datagram + Distribution Server). Repeat this option to set secondary NBDD + server addresses. + + :code:`NTP` ``address`` + Set primary NTP server address (Network Time Protocol). + Repeat this option to set secondary NTP server addresses. + + :code:`NBT` ``type`` + Set NetBIOS over TCP/IP Node type. Possible options: + + :code:`1` + b-node (broadcasts) + + :code:`2` + p-node (point-to-point name queries to a WINS server) + + :code:`4` + m-node (broadcast then query name server) + + :code:`8` + h-node (query name server, then broadcast). + + :code:`NBS` ``scope-id`` + Set NetBIOS over TCP/IP Scope. A NetBIOS Scope ID provides an + extended naming service for the NetBIOS over TCP/IP (Known as NBT) + module. The primary purpose of a NetBIOS scope ID is to isolate + NetBIOS traffic on a single network to only those nodes with the + same NetBIOS scope ID. The NetBIOS scope ID is a character string + that is appended to the NetBIOS name. The NetBIOS scope ID on two + hosts must match, or the two hosts will not be able to communicate. + The NetBIOS Scope ID also allows computers to use the same computer + name, as they have different scope IDs. The Scope ID becomes a part + of the NetBIOS name, making the name unique. (This description of + NetBIOS scopes courtesy of NeonSurge@abyss.com) + + :code:`DISABLE-NBT` + Disable Netbios-over-TCP/IP. + +--ifconfig args + Set TUN/TAP adapter parameters. It requires the *IP address* of the local + VPN endpoint. For TUN devices in point-to-point mode, the next argument + must be the VPN IP address of the remote VPN endpoint. For TAP devices, + or TUN devices used with ``--topology subnet``, the second argument + is the subnet mask of the virtual network segment which is being created + or connected to. + + For TUN devices, which facilitate virtual point-to-point IP connections + (when used in ``--topology net30`` or ``p2p`` mode), the proper usage of + ``--ifconfig`` is to use two private IP addresses which are not a member + of any existing subnet which is in use. The IP addresses may be + consecutive and should have their order reversed on the remote peer. + After the VPN is established, by pinging ``rn``, you will be pinging + across the VPN. + + For TAP devices, which provide the ability to create virtual ethernet + segments, or TUN devices in ``--topology subnet`` mode (which create + virtual "multipoint networks"), ``--ifconfig`` is used to set an IP + address and subnet mask just as a physical ethernet adapter would be + similarly configured. If you are attempting to connect to a remote + ethernet bridge, the IP address and subnet should be set to values which + would be valid on the the bridged ethernet segment (note also that DHCP + can be used for the same purpose). + + This option, while primarily a proxy for the ``ifconfig``\(8) command, + is designed to simplify TUN/TAP tunnel configuration by providing a + standard interface to the different ifconfig implementations on + different platforms. + + ``--ifconfig`` parameters which are IP addresses can also be specified + as a DNS or /etc/hosts file resolvable name. + + For TAP devices, ``--ifconfig`` should not be used if the TAP interface + will be getting an IP address lease from a DHCP server. + + Examples: + :: + + # tun device in net30/p2p mode + ifconfig 10.8.0.2 10.8.0.1 + + # tun/tap device in subnet mode + ifconfig 10.8.0.2 255.255.255.0 + +--ifconfig-ipv6 args + Configure an IPv6 address on the *tun* device. + + Valid syntax: + :: + + ifconfig-ipv6 ipv6addr/bits [ipv6remote] + + The ``ipv6addr/bits`` argument is the IPv6 address to use. The + second parameter is used as route target for ``--route-ipv6`` if no + gateway is specified. + + The ``--topology`` option has no influence with ``--ifconfig-ipv6`` + +--ifconfig-noexec + Don't actually execute ifconfig/netsh commands, instead pass + ``--ifconfig`` parameters to scripts using environmental variables. + +--ifconfig-nowarn + Don't output an options consistency check warning if the ``--ifconfig`` + option on this side of the connection doesn't match the remote side. + This is useful when you want to retain the overall benefits of the + options consistency check (also see ``--disable-occ`` option) while only + disabling the ifconfig component of the check. + + For example, if you have a configuration where the local host uses + ``--ifconfig`` but the remote host does not, use ``--ifconfig-nowarn`` + on the local host. + + This option will also silence warnings about potential address conflicts + which occasionally annoy more experienced users by triggering "false + positive" warnings. + +--lladdr address + Specify the link layer address, more commonly known as the MAC address. + Only applied to TAP devices. + +--persist-tun + Don't close and reopen TUN/TAP device or run up/down scripts across + :code:`SIGUSR1` or ``--ping-restart`` restarts. + + :code:`SIGUSR1` is a restart signal similar to :code:`SIGHUP`, but which + offers finer-grained control over reset options. + +--redirect-gateway flags + Automatically execute routing commands to cause all outgoing IP traffic + to be redirected over the VPN. This is a client-side option. + + This option performs three steps: + + (1) Create a static route for the ``--remote`` address which + forwards to the pre-existing default gateway. This is done so that + ``(3)`` will not create a routing loop. + + (2) Delete the default gateway route. + + (3) Set the new default gateway to be the VPN endpoint address + (derived either from ``--route-gateway`` or the second parameter to + ``--ifconfig`` when ``--dev tun`` is specified). + + When the tunnel is torn down, all of the above steps are reversed so + that the original default route is restored. + + Option flags: + + :code:`local` + Add the :code:`local` flag if both OpenVPN peers are directly + connected via a common subnet, such as with wireless. The + :code:`local` flag will cause step ``(1)`` above to be omitted. + + :code:`autolocal` + Try to automatically determine whether to enable :code:`local` + flag above. + + :code:`def1` + Use this flag to override the default gateway by using + :code:`0.0.0.0/1` and :code:`128.0.0.0/1` rather than + :code:`0.0.0.0/0`. This has the benefit of overriding but not + wiping out the original default gateway. + + :code:`bypass-dhcp` + Add a direct route to the DHCP server (if it is non-local) which + bypasses the tunnel (Available on Windows clients, may not be + available on non-Windows clients). + + :code:`bypass-dns` + Add a direct route to the DNS server(s) (if they are non-local) + which bypasses the tunnel (Available on Windows clients, may + not be available on non-Windows clients). + + :code:`block-local` + Block access to local LAN when the tunnel is active, except for + the LAN gateway itself. This is accomplished by routing the local + LAN (except for the LAN gateway address) into the tunnel. + + :code:`ipv6` + Redirect IPv6 routing into the tunnel. This works similar to + the :code:`def1` flag, that is, more specific IPv6 routes are added + (:code:`2000::/4`, :code:`3000::/4`), covering the whole IPv6 + unicast space. + + :code:`!ipv4` + Do not redirect IPv4 traffic - typically used in the flag pair + :code:`ipv6 !ipv4` to redirect IPv6-only. + +--redirect-private flags + Like ``--redirect-gateway``, but omit actually changing the default gateway. + Useful when pushing private subnets. + +--route args + Add route to routing table after connection is established. Multiple + routes can be specified. Routes will be automatically torn down in + reverse order prior to TUN/TAP device close. + + Valid syntaxes: + :: + + route network/IP + route network/IP netmask + route network/IP netmask gateway + route network/IP netmask gateway metric + + This option is intended as a convenience proxy for the ``route``\(8) + shell command, while at the same time providing portable semantics + across OpenVPN's platform space. + + ``netmask`` + defaults to :code:`255.255.255.255` when not given + + ``gateway`` + default taken from ``--route-gateway`` or the second + parameter to ``--ifconfig`` when ``--dev tun`` is specified. + + ``metric`` + default taken from ``--route-metric`` if set, otherwise :code:`0`. + + The default can be specified by leaving an option blank or setting it to + :code:`default`. + + The ``network`` and ``gateway`` parameters can also be specified as a + DNS or :code:`/etc/hosts` file resolvable name, or as one of three special + keywords: + + :code:`vpn_gateway` + The remote VPN endpoint address (derived either from + ``--route-gateway`` or the second parameter to ``--ifconfig`` + when ``--dev tun`` is specified). + + :code:`net_gateway` + The pre-existing IP default gateway, read from the + routing table (not supported on all OSes). + + :code:`remote_host` + The ``--remote`` address if OpenVPN is being run in + client mode, and is undefined in server mode. + +--route-delay args + Valid syntaxes: + :: + + route-delay + route-delay n + route-delay n m + + Delay ``n`` seconds (default :code:`0`) after connection establishment, + before adding routes. If ``n`` is :code:`0`, routes will be added + immediately upon connection establishment. If ``--route-delay`` is + omitted, routes will be added immediately after TUN/TAP device open and + ``--up`` script execution, before any ``--user`` or ``--group`` privilege + downgrade (or ``--chroot`` execution.) + + This option is designed to be useful in scenarios where DHCP is used to + set tap adapter addresses. The delay will give the DHCP handshake time + to complete before routes are added. + + On Windows, ``--route-delay`` tries to be more intelligent by waiting + ``w`` seconds (default :code:`30` by default) for the TAP-Win32 adapter + to come up before adding routes. + +--route-ipv6 args + Setup IPv6 routing in the system to send the specified IPv6 network into + OpenVPN's *tun*. + + Valid syntax: + :: + + route-ipv6 ipv6addr/bits [gateway] [metric] + + The gateway parameter is only used for IPv6 routes across *tap* devices, + and if missing, the ``ipv6remote`` field from ``--ifconfig-ipv6`` or + ``--route-ipv6-gateway`` is used. + +--route-gateway arg + Specify a default *gateway* for use with ``--route``. + + If :code:`dhcp` is specified as the parameter, the gateway address will + be extracted from a DHCP negotiation with the OpenVPN server-side LAN. + + Valid syntaxes: + :: + + route-gateway gateway + route-gateway dhcp + +--route-ipv6-gateway gw + Specify a default gateway ``gw`` for use with ``--route-ipv6``. + +--route-metric m + Specify a default metric ``m`` for use with ``--route``. + +--route-noexec + Don't add or remove routes automatically. Instead pass routes to + ``--route-up`` script using environmental variables. + +--route-nopull + When used with ``--client`` or ``--pull``, accept options pushed by + server EXCEPT for routes, block-outside-dns and dhcp options like DNS + servers. + + When used on the client, this option effectively bars the server from + adding routes to the client's routing table, however note that this + option still allows the server to set the TCP/IP properties of the + client's TUN/TAP interface. + +--topology mode + Configure virtual addressing topology when running in ``--dev tun`` + mode. This directive has no meaning in ``--dev tap`` mode, which always + uses a :code:`subnet` topology. + + If you set this directive on the server, the ``--server`` and + ``--server-bridge`` directives will automatically push your chosen + topology setting to clients as well. This directive can also be manually + pushed to clients. Like the ``--dev`` directive, this directive must + always be compatible between client and server. + + ``mode`` can be one of: + + :code:`net30` + Use a point-to-point topology, by allocating one /30 subnet + per client. This is designed to allow point-to-point semantics when some + or all of the connecting clients might be Windows systems. This is the + default on OpenVPN 2.0. + + :code:`p2p` + Use a point-to-point topology where the remote endpoint of + the client's tun interface always points to the local endpoint of the + server's tun interface. This mode allocates a single IP address per + connecting client. Only use when none of the connecting clients are + Windows systems. + + :code:`subnet` + Use a subnet rather than a point-to-point topology by + configuring the tun interface with a local IP address and subnet mask, + similar to the topology used in ``--dev tap`` and ethernet bridging + mode. This mode allocates a single IP address per connecting client and + works on Windows as well. Only available when server and clients are + OpenVPN 2.1 or higher, or OpenVPN 2.0.x which has been manually patched + with the ``--topology`` directive code. When used on Windows, requires + version 8.2 or higher of the TAP-Win32 driver. When used on \*nix, + requires that the tun driver supports an ``ifconfig``\(8) command which + sets a subnet instead of a remote endpoint IP address. + + *Note:* Using ``--topology subnet`` changes the interpretation of the + arguments of ``--ifconfig`` to mean "address netmask", no longer "local + remote". + +--tun-mtu n + Take the TUN device MTU to be **n** and derive the link MTU from it + (default :code:`1500`). In most cases, you will probably want to leave + this parameter set to its default value. + + The MTU (Maximum Transmission Units) is the maximum datagram size in + bytes that can be sent unfragmented over a particular network path. + OpenVPN requires that packets on the control and data channels be sent + unfragmented. + + MTU problems often manifest themselves as connections which hang during + periods of active usage. + + It's best to use the ``--fragment`` and/or ``--mssfix`` options to deal + with MTU sizing issues. + +--tun-mtu-extra n + Assume that the TUN/TAP device might return as many as ``n`` bytes more + than the ``--tun-mtu`` size on read. This parameter defaults to 0, which + is sufficient for most TUN devices. TAP devices may introduce additional + overhead in excess of the MTU size, and a setting of 32 is the default + when TAP devices are used. This parameter only controls internal OpenVPN + buffer sizing, so there is no transmission overhead associated with + using a larger value. + + +TUN/TAP standalone operations +----------------------------- +These two standalone operations will require ``--dev`` and optionally +``--user`` and/or ``--group``. + +--mktun + (Standalone) Create a persistent tunnel on platforms which support them + such as Linux. Normally TUN/TAP tunnels exist only for the period of + time that an application has them open. This option takes advantage of + the TUN/TAP driver's ability to build persistent tunnels that live + through multiple instantiations of OpenVPN and die only when they are + deleted or the machine is rebooted. + + One of the advantages of persistent tunnels is that they eliminate the + need for separate ``--up`` and ``--down`` scripts to run the appropriate + ``ifconfig``\(8) and ``route``\(8) commands. These commands can be + placed in the the same shell script which starts or terminates an + OpenVPN session. + + Another advantage is that open connections through the TUN/TAP-based + tunnel will not be reset if the OpenVPN peer restarts. This can be + useful to provide uninterrupted connectivity through the tunnel in the + event of a DHCP reset of the peer's public IP address (see the + ``--ipchange`` option above). + + One disadvantage of persistent tunnels is that it is harder to + automatically configure their MTU value (see ``--link-mtu`` and + ``--tun-mtu`` above). + + On some platforms such as Windows, TAP-Win32 tunnels are persistent by + default. + +--rmtun + (Standalone) Remove a persistent tunnel. -- cgit v1.2.3