Description: Man page fixes
Author: Alberto Gonzalez Iniesta <agi@inittab.org>
Index: openvpn/doc/openvpn.8
===================================================================
--- openvpn.orig/doc/openvpn.8	2013-05-17 12:04:17.678140187 +0200
+++ openvpn/doc/openvpn.8	2013-05-17 12:04:17.674140147 +0200
@@ -21,13 +21,13 @@
 .\"  59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
 .\"
 .\" Manual page for openvpn
-.\
+.\"
 .\" SH section heading
 .\" SS subsection heading
 .\" LP paragraph
 .\" IP indented paragraph
 .\" TP hanging label
-.\
+.\"
 .\" .nf -- no formatting
 .\" .fi -- resume formatting
 .\" .ft 3 -- boldface
@@ -2513,7 +2513,7 @@
 .B \-\-management-signal
 Send SIGUSR1 signal to OpenVPN if management session disconnects.
 This is useful when you wish to disconnect an OpenVPN session on
-user logoff. For --management-client this option is not needed since
+user logoff. For \-\-management-client this option is not needed since
 a disconnect will always generate a SIGTERM.
 .\"*********************************************************
 .TP
@@ -3889,7 +3889,7 @@
 This option is only relevant in UDP mode, i.e.
 when either
 .B \-\-proto udp
-is specifed, or no
+is specified, or no
 .B \-\-proto
 option is specified.
 
@@ -5012,7 +5012,7 @@
 
 This option have changed behaviour in OpenVPN 2.3.  Earlier you had to
 define
-.B --win-sys env
+.B \-\-win-sys env
 to use the SystemRoot environment variable, otherwise it defaulted to C:\\WINDOWS.
 It is not needed to use the
 .B env
@@ -5055,7 +5055,7 @@
 .B \-\-dev tun
 mode, OpenVPN will cause the DHCP server to masquerade as if it were
 coming from the remote endpoint.  The optional offset parameter is
-an integer which is > -256 and < 256 and which defaults to 0.
+an integer which is > \-256 and < 256 and which defaults to 0.
 If offset is positive, the DHCP server will masquerade as the IP
 address at network address + offset.
 If offset is negative, the DHCP server will masquerade as the IP
@@ -5349,26 +5349,26 @@
 documentation of the IPv6-related options. More documentation can be
 found on http://www.greenie.net/ipv6/openvpn.html.
 .TP
-.B --ifconfig-ipv6 ipv6addr/bits ipv6remote
+.B \-\-ifconfig-ipv6 ipv6addr/bits ipv6remote
 configure IPv6 address
 .B ipv6addr/bits
 on the ``tun'' device.  The second parameter is used as route target for
-.B --route-ipv6
+.B \-\-route-ipv6
 if no gateway is specified.
 .TP
-.B --route-ipv6 ipv6addr/bits [gateway] [metric]
+.B \-\-route-ipv6 ipv6addr/bits [gateway] [metric]
 setup IPv6 routing in the system to send the specified IPv6 network
 into OpenVPN's ``tun'' device
 .TP
-.B --server-ipv6 ipv6addr/bits
+.B \-\-server-ipv6 ipv6addr/bits
 convenience-function to enable a number of IPv6 related options at
 once, namely
-.B --ifconfig-ipv6, --ifconfig-ipv6-pool, --tun-ipv6
+.B \-\-ifconfig-ipv6, \-\-ifconfig-ipv6-pool, \-\-tun-ipv6
 and
-.B --push tun-ipv6
-Is only accepted if ``--mode server'' or ``--server'' is set.
+.B \-\-push tun-ipv6
+Is only accepted if ``\-\-mode server'' or ``\-\-server'' is set.
 .TP
-.B --ifconfig-ipv6-pool ipv6addr/bits
+.B \-\-ifconfig-ipv6-pool ipv6addr/bits
 Specify an IPv6 address pool for dynamic assignment to clients.  The
 pool starts at
 .B ipv6addr
@@ -5376,20 +5376,20 @@
 .B /bits
 setting controls the size of the pool.
 .TP
-.B --ifconfig-ipv6-push ipv6addr/bits ipv6remote
+.B \-\-ifconfig-ipv6-push ipv6addr/bits ipv6remote
 for ccd/ per-client static IPv6 interface configuration, see
-.B --client-config-dir
+.B \-\-client-config-dir
 and
-.B --ifconfig-push
+.B \-\-ifconfig-push
 for more details.
 .TP
-.B --iroute-ipv6 ipv6addr/bits
+.B \-\-iroute-ipv6 ipv6addr/bits
 for ccd/ per-client static IPv6 route configuration, see
-.B --iroute
+.B \-\-iroute
 for more details how to setup and use this, and how
-.B --iroute
+.B \-\-iroute
 and
-.B --route
+.B \-\-route
 interact.
 
 .\"*********************************************************
@@ -5875,7 +5875,7 @@
 .TP
 .B peer_cert
 Temporary file name containing the client certificate upon
-connection.  Useful in conjunction with --tls-verify
+connection.  Useful in conjunction with \-\-tls-verify
 .\"*********************************************************
 .TP
 .B script_context