Initial import of sane-backends version 1.0.24-1.2

1 files changed, 184 insertions, 0 deletions

diff --git a/backend/plustek.conf.in b/backend/plustek.conf.in
new file mode 100644
index 0000000..e16823e
--- /dev/null
+++ b/backend/plustek.conf.in
@@ -0,0 +1,184 @@
+# Plustek-SANE Backend configuration file
+# For use with LM9831/2/3 based USB scanners
+#
+
+# each device needs at least two lines:
+# - [usb] vendor-ID and product-ID
+# - device devicename
+# i.e. for Plustek (0x07B3) UT12/16/24 (0x0017)
+# [usb] 0x07B3 0x0017
+# device /dev/usbscanner
+# or
+# device libusb:bbb:ddd
+# where bbb is the busnumber and ddd the device number
+# make sure that your user has access to /proc/bus/usb/bbb/ddd
+#
+# additionally you can specify some options
+# warmup, lOffOnEnd, lampOff
+#
+# For autodetection use
+# [usb]
+# device /dev/usbscanner
+#
+# or simply
+# [usb]
+#
+# or if you want a specific device but you have no idea about the
+# device node or you use libusb, simply set vendor- and product-ID
+# [usb] 0x07B3 0x0017
+# device auto
+#
+# NOTE: autodetection is safe, as it uses the info it got
+#       from the USB subsystem. If you're not using the
+#       autodetection, you MUST have attached that device
+#       at your USB-port, that you have specified...
+#
+
+[usb]
+
+#
+# options for the previous USB entry
+#
+# switch lamp off after xxx secs, 0 disables the feature
+# (can also be set via frontend)
+option lampOff 300
+
+# warmup period in seconds, 0 means no warmup, -1 means auto-warmup
+# (can also be set via frontend)
+option warmup -1
+
+# 0 means leave lamp-status untouched, not 0 means switch off
+# on sane_close
+# (can also be set via frontend)
+option lOffOnEnd 1
+
+#
+# options to tweak the image start-position
+# (WARNING: there's no internal range check!!!)
+#
+# for the normal scan area
+#
+option posOffX 0
+option posOffY 0
+
+# for transparencies
+option tpaOffX 0
+option tpaOffY 0
+
+# for negatives
+option negOffX 0
+option negOffY 0
+
+#
+# for setting the calibration strip position
+# (WARNING: there's no internal range check!!!)
+# -1 means use built in
+# (can also be set via frontend)
+option posShadingY -1
+option tpaShadingY -1
+option negShadingY -1
+
+#
+# to invert the negatives, 0 disables the feature
+#
+option invertNegatives 0
+
+#
+# to disable the internal sensor speedup function, 
+# 1 disables the feature
+#
+option disableSpeedup 0
+
+#
+# to save/restore coarse calibration data
+# (can also be set via frontend)
+option cacheCalData 0
+
+#
+# use alternate calibration routines
+#
+option altCalibration 0
+
+#
+# for skipping whole calibration step
+#
+option skipCalibration 0
+
+#
+# for skipping entire fine calibration step
+# coarse calibration is done
+#
+option skipFine 0
+
+#
+# discard the result of the fine white calibration
+#
+option skipFineWhite 0
+
+#
+# some scanners have a dark calibration strip, in
+# general this one should be used for calibration.
+# As this could cause some trouble, this option
+# overrides that and the dark calibration will be
+# done by switching the lamp off
+#
+option skipDarkStrip 0
+
+# for replacing the gain values found during coarse
+# calibration
+# (can also be set via frontend)
+option red_gain   -1
+option green_gain -1
+option blue_gain  -1
+
+# for replacing the offset values found during coarse
+# calibration
+# (can also be set via frontend)
+option red_offset   -1
+option green_offset -1
+option blue_offset  -1
+
+#
+# for replacing the default lampoff settings, this
+# works only for CIS devices like CanoScan LiDE20
+# (can also be set via frontend)
+option red_lampoff   -1
+option green_lampoff -1
+option blue_lampoff  -1
+
+#
+# for adjusting the default gamma values
+# (can also be set via frontend)
+option redGamma         1.0
+option greenGamma       1.0
+option blueGamma        1.0
+option grayGamma        1.0
+
+#
+# to enable TPA (EPSON or UMAX, if autodetection fails)
+# 0 means default behaviour as specified in the internal tables
+# 1 means enable (needed for UMAX 3450)
+option enableTPA 0
+
+#
+# model override functionality, currently only available for
+# Mustek devices, using NSCs' vendor ID: 0x0400 and
+# also their product ID: 0x1000 (LM9831) 0x1001 (LM9832)
+#
+# mov/PID    |    0x1000   |   0x1001
+# ---------------------------------------
+# 0 (default)| BearPaw1200 | BearPaw 2400
+# 1          |   ignored   | BearPaw 1200
+#
+option mov 0
+
+#
+# and of course the device-name
+#
+# device /dev/usbscanner
+device auto
+
+#
+# to define a new device, start with a new section:
+# [usb] 
+#