New upstream version 1.0.28upstream/1.0.28

1 files changed, 37 insertions, 36 deletions

diff --git a/doc/sane-p5.man b/doc/sane-p5.man
index 860a019..1c21f12 100644
--- a/doc/sane-p5.man
+++ b/doc/sane-p5.man
@@ -7,28 +7,28 @@ The
 .B sane\-p5
 library implements a SANE (Scanner Access Now Easy) backend that
 provides access to the Primax PagePartner parallel port sheet fed scanner.
-.PP 
+.PP
 This backend handles 100, 150, 200, 300 and 600 dpi scan resolutions,
 in color and gray modes. The 600 dpi is actually 300x600 with lines
 enlarged to match the vertical resolution.
-.PP 
+.PP
 .B EPP/ECP MODES ONLY
-The current version of the backend uses only EPP or ECP mode to communicate 
-with the scanner. It is 
-recommended that you set your parallel port to EPP in BIOS with the current 
+The current version of the backend uses only EPP or ECP mode to communicate
+with the scanner. It is
+recommended that you set your parallel port to EPP in BIOS with the current
 version of this backend. ECPEPP will only
 work if you use a 2.4 or 2.6 kernel with ppdev character device support.
-.PP 
+.PP
 
 .SH "DEVICE NAMES"
 This backend expects device names of the form:
-.PP 
+.PP
 .RS
 .I port value
 .RE
-.PP 
+.PP
 Where
-\fBvalue\fR is : 
+\fBvalue\fR is :
 
 .RS
 .TP
@@ -40,43 +40,43 @@ them for scanner
 uses linux ppdev device, depending on the
 number of available parallel port, you
 have to use /dev/parport1, /dev/parport2, ...
-.PP 
+.PP
 .RE
 You can rename any device using the
-.PP 
+.PP
 .RS
 .br
 .I option name my_name
 .RE
-.PP 
-option. This option apply to the last port option. 
+.PP
+option. This option apply to the last port option.
 
 .SH "CONFIGURATION"
 Please make sure to edit dll.conf
 .B before
 you use the backend, since this backend isn't enabled by default.
-.PP 
+.PP
 
-.PP 
+.PP
 
 
 
 .SH "FILES"
-.TP 
+.TP
 .I @CONFIGDIR@/p5.conf
 The backend configuration file (see also description of
 .B SANE_CONFIG_DIR
 below).
-.TP 
+.TP
 .I @LIBDIR@/libsane\-p5.a
 The static library implementing this backend.
-.TP 
+.TP
 .I @LIBDIR@/libsane\-p5.so
 The shared library implementing this backend (present on systems that
 support dynamic loading).
 
 .SH "ENVIRONMENT"
-.TP 
+.TP
 .B SANE_CONFIG_DIR
 This environment variable specifies the list of directories that may
 contain the configuration file.  Under UNIX, the directories are
@@ -90,14 +90,14 @@ directories.  For example, setting
 .B SANE_CONFIG_DIR
 to "/tmp/config:" would result in directories "tmp/config", ".", and
 "@CONFIGDIR@" being searched (in this order).
-.TP 
+.TP
 .B SANE_DEBUG_P5
 If the library was compiled with debug support enabled, this
 environment variable controls the debug level for this backend.  E.g.,
 a value of 255 requests all debug output to be printed.  Smaller
 levels reduce verbosity.
 
-.PP 
+.PP
 .RS
 .ft CR
 .nf
@@ -108,23 +108,23 @@ level   debug output
  2       warnings & minor errors
  4       information messages
  8       start/stop of functions
- 16      tracing messages              
+ 16      tracing messages
  32      I/O functions
  64      I/O functions with traces
  128     scanned/calibration data
 .fi
 .ft R
 .RE
-.PP 
-.TP 
+.PP
+.TP
 
-.PP 
+.PP
 .RS
 .ft CR
 .nf
-.PP 
- 
-.PP 
+.PP
+
+.PP
 .SH "SEE ALSO"
 sane(7), sane\-net(5), saned(8)
 
@@ -136,25 +136,26 @@ Support for the Prima PagePartner has been made possible thank to an hardware do
 by S\['e]bastien Lange.
 
 .SH "BUG REPORTS"
-If something doesn't work mail sane-devel@lists.alioth.debian.org or use the bug
-tracker at https://alioth.debian.org/tracker/?atid=410366&group_id=30186 .
-Please give as much information as you can. 
+If something doesn't work mail sane-devel@alioth-lists.debian.net or submit an
+issue via https://gitlab.com/sane-project/backends/issues/new with a label of
+backend/p5.
+Please give as much information as you can.
 
-.TP 
+.TP
 .I SANE version
 run "scanimage \-V" to determine this
-.TP 
+.TP
 .I the backend version and your scanner hardware
 run "SANE_DEBUG_P5=255 scanimage \-L 2>log" as root. If you don't get any output
 from the p5 backend, make sure a line "p5" is included into
 your @CONFIGDIR@/dll.conf.
 If your scanner isn't detected, make sure you've defined the right port address, or the
-correct device 
+correct device
 in your p5.conf.
-.TP 
+.TP
 .I the name of your scanner/vendor
 also a worthy information. Please also include the optical resolution and lamp type of your scanner, both can be found in the manual of your scanner.
-.TP 
+.TP
 .I any further comments
 if you have comments about the documentation (what could be done better), or you
 think I should know something, please include it.