diff options
Diffstat (limited to 'doc/sane-dc210.man')
| -rw-r--r-- | doc/sane-dc210.man | 36 |
1 files changed, 25 insertions, 11 deletions
diff --git a/doc/sane-dc210.man b/doc/sane-dc210.man index 7d3ad65..89e9e72 100644 --- a/doc/sane-dc210.man +++ b/doc/sane-dc210.man @@ -14,22 +14,28 @@ connected. The device name is always "0". .SH CONFIGURATION The contents of the .I dc210.conf -specify the serial port and baud rate to use. The baud rate -specifies the maximum rate to use while downloading pictures. (The +specify the serial port and baud rate to use. The +.B baud +rate specifies the maximum rate to use while downloading pictures. (The camera is always initialized using 9600 baud, then switches to the higher rate). On my 90MHz Pentium, I usually have no problems downloading at 115200 baud as long as the system is not excessively busy and -the "interrupt-unmask flag" is set in the IDE driver (hdparm \-u1). +the "interrupt-unmask flag" is set in the IDE driver +.RI ( "hdparm \-u1" ). Supported baud rates are: 9600, 19200, 38400, 57600, and 115200. .PP -The dumpinquiry line causes some information about the camera to +The +.B dumpinquiry +line causes some information about the camera to be printed. .PP -cmdrespause specifies how many usec (1,000,000ths of a) between +.B cmdrespause +specifies how many usec (1,000,000ths of a) between writing the command and reading the result should be used. 125000 seems to be the lowest I could go reliably. .PP -breakpause is the time in 1,000,000ths of a usec between sending the +.B breakpause +is the time in 1,000,000ths of a usec between sending the "back to default" break sending commands. .PP Empty lines and lines starting with a hash mark (#) are @@ -71,13 +77,19 @@ contain the configuration file. Under UNIX, the directories are separated by a colon (`:'), under OS/2, they are separated by a semi-colon (`;'). If this variable is not set, the configuration file is searched in two default directories: first, the current working -directory (".") and then in @CONFIGDIR@. If the value of the +directory (".") and then in +.IR @CONFIGDIR@. +If the value of the environment variable ends with the directory separator character, then the default directories are searched after the explicitly specified directories. For example, setting .B SANE_CONFIG_DIR -to "/tmp/config:" would result in directories "tmp/config", ".", and -"@CONFIGDIR@" being searched (in this order). +to "/tmp/config:" would result in directories +.IR "tmp/config", +.IR ".", +and +.I "@CONFIGDIR@" +being searched (in this order). .TP .B SANE_DEBUG_DC210 If the library was compiled with debugging support enabled, this @@ -86,7 +98,7 @@ A value of 128 requests maximally copious debug output; smaller levels reduce verbosity. .SH "SEE ALSO" -sane(7) +.BR sane (7) .SH AUTHOR Brian J. Murrell @@ -102,6 +114,8 @@ Known bugs/limitations are: ? .PP More general comments, suggestions, and inquiries about frontends or SANE should go to the SANE Developers mailing list -(see http://www.sane\-project.org/mailing\-lists.html for details). +(see +.I http://www.sane\-project.org/mailing\-lists.html +for details). You must be subscribed to the list, otherwise your mail won't be sent to the subscribers. |