From 351b7328520c16730ceb46e5acae16038c42185e Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?J=C3=B6rg=20Frings-F=C3=BCrst?= Date: Tue, 16 Feb 2021 18:24:19 +0100 Subject: New upstream version 1.0.32 --- doc/plustek/FAQ | 4 ++-- doc/plustek/Plustek-PARPORT.changes | 4 ++-- doc/plustek/Plustek-USB.txt | 6 +++--- 3 files changed, 7 insertions(+), 7 deletions(-) (limited to 'doc/plustek') diff --git a/doc/plustek/FAQ b/doc/plustek/FAQ index a3a224f..92a4e72 100644 --- a/doc/plustek/FAQ +++ b/doc/plustek/FAQ @@ -111,7 +111,7 @@ SOLUTION: --------- Simply load the parport module. You can add this dependency to your /etc/modules.conf (or /etc/conf.modules) file (see INSTALL). -Then everytime you load pt_drv with modprobe, parport will be loaded +Then every time you load pt_drv with modprobe, parport will be loaded automatically. After modifying this file, call depmod -va @@ -339,7 +339,7 @@ A: I recommend to uninstall the previous one. rpm -e sane-1.0.1-94 - After theses steps, sane should be removed. + After these steps, sane should be removed. I'm not sure, but you might have to remove the /etc/sane.d manually... Now got to your sane-1.0.3 stuff and reinstall this as described. Before using, you might have a look diff --git a/doc/plustek/Plustek-PARPORT.changes b/doc/plustek/Plustek-PARPORT.changes index 6aa878b..43131f7 100644 --- a/doc/plustek/Plustek-PARPORT.changes +++ b/doc/plustek/Plustek-PARPORT.changes @@ -97,7 +97,7 @@ Version 0.39 08/11/2001 3.0 Added forceMode switch 4.0 Fixed a problem in the PT12 code that causes I/O timeouts 5.0 Added Genius Colorpage Vivivd III V2 stuff - 6.0 Added A3I stuff aquired from Plustek + 6.0 Added A3I stuff acquired from Plustek 7.0 Fixed a bug, that causes some seg-faults Version 0.40 12/17/2001 @@ -110,7 +110,7 @@ Version 0.41 01/10/2002 1.0 Changed IOCTL interface to the kernel module to allow adjustment of some driver internal variables 2.0 Changed plustek.conf configuration fileformat to reflect the enhanced - capabilites + capabilities Version 0.42 02/12/2002 1.0 Added custom gamma table support diff --git a/doc/plustek/Plustek-USB.txt b/doc/plustek/Plustek-USB.txt index 939d4d7..29989d0 100644 --- a/doc/plustek/Plustek-USB.txt +++ b/doc/plustek/Plustek-USB.txt @@ -195,7 +195,7 @@ When using libusb with SANE, then you should also use the hotplug utilities to automatically setup your device nodes (at least the permissions) and prevent scanner.o from loading. -Assuming, that these utilites are properly installed on your box, you have +Assuming, that these utilities are properly installed on your box, you have to tweak and add some files. In directory (where of course the config files reside): @@ -292,7 +292,7 @@ it. If you have carried out all of the above steps, then sane-find-scanner should be able to recognise your scanner correctly. -sane-find-scanner probes all of the devices on the SCSI and USB busses, and +sane-find-scanner probes all of the devices on the SCSI and USB buses, and so you may find that it outputs "unable to get minor data" errors or similar to your terminal, or to your error logs, you can safely ignore these as long as it does that, and has recognised your scanner. @@ -339,7 +339,7 @@ log, as well as (where possible) the output of the scanimage command (if you can't capture it directly, an as-accurate-as-possible description is MUCH better than nothing!), and try and get all of the activity that your scanner did as well (light -came on? didnt? motors came on? etc?) and email that to the plustek list +came on? didn't? motors came on? etc?) and email that to the plustek list (). For the particularly adventurous only... -- cgit v1.2.3