From 351b7328520c16730ceb46e5acae16038c42185e Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?J=C3=B6rg=20Frings-F=C3=BCrst?= Date: Tue, 16 Feb 2021 18:24:19 +0100 Subject: New upstream version 1.0.32 --- doc/sane-sm3840.man | 48 ++++++++++++++++++++++++++++++------------------ 1 file changed, 30 insertions(+), 18 deletions(-) (limited to 'doc/sane-sm3840.man') diff --git a/doc/sane-sm3840.man b/doc/sane-sm3840.man index e6af3a1..58f07b0 100644 --- a/doc/sane-sm3840.man +++ b/doc/sane-sm3840.man @@ -10,10 +10,15 @@ provides access to some Microtek scanners with the SCAN08 USB chip. .PP There exist backends for Microtek scanners with SCSI command set. -Refer to sane\-microtek(5) and sane\-microtek2(5) for details. +Refer to +.BR sane\-microtek (5) +and +.BR sane\-microtek2 (5) +for details. .PP -There also exists a Microtek 3600 series driver, see sane\-sm3600(5) for -details. +There also exists a Microtek 3600 series driver, see +.BR sane\-sm3600 (5) +for details. .PP At present, the following scanners are known positively to work with this backend: @@ -31,36 +36,38 @@ Microtek ScanMaker 4800 All modes OK .PP If you own a Microtek scanner with the SCAN08 chip other than the ones listed above, it may or may not work with SANE. Feel free to contact the -backend author (earle@ziplabel.com) to report results with scanners not -on the list. +backend author +.RI ( earle@ziplabel.com ) +to report results with scanners not on the list. .SH "FRONTEND OPTIONS" .PP -The following options are supported by the sm3840-driver: -.PP +The following options are supported by the +.BR sane\-sm3840 +driver: +.TP .B \-\-mode color|gray|lineart|halftone -.br Color or grayscale mode. +.TP .B \-\-resolution 150|300|600|1200 -.br Pixels per inch for scans. +.TP .B \-\-depth 8|16 -.br Note that the least significant bits of 16bpp mode may be noise. +.TP .B \-\-brightness 1..4096 -.br Higher numbers increase brightness of returned image. +.TP .B \-\-contrast 0.1..9.9 -.br Larger numbers decrease contrast of returned image. +.TP .B \-\-lamp\-timeout 1..15 -.br Time in minutes until the lamp is turned off after a scan. .SH CONFIGURATION @@ -83,12 +90,17 @@ If the library was compiled with debug support enabled, this environment variable controls the debug level for this backend. E.g., a value of 128 requests all debug output to be printed. Smaller levels reduce verbosity. To see error messages on stderr set -SANE_DEBUG_SM3840 to 1. +.B SANE_DEBUG_SM3840 +to 1. .SH "SEE ALSO" -sane\-microtek2(5), sane\-sm3600(5), http://www.ziplabel.com/sm3840 +.BR sane (7), +.BR sane\-microtek (5), +.BR sane\-microtek2 (5), +.BR sane\-sm3600 (5) +.br +.I http://www.ziplabel.com/sm3840 .SH AUTHOR -.br -Earle F. Philhower III (earle@ziplabel.com) -.br +Earle F. Philhower III +.RI < earle@ziplabel.com > -- cgit v1.2.3