1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
|
.TH sane\-dc240 5 "11 Jul 2008" "@PACKAGEVERSION@" "SANE Scanner Access Now Easy"
.IX sane\-dc240
.SH NAME
sane\-dc240 \- SANE backend for Kodak DC240 Digital Camera
.SH DESCRIPTION
The
.B sane\-dc240
library implements a SANE (Scanner Access Now Easy) backend that
provides access to the Kodak DC240 camera. THIS IS EXTREMELY ALPHA
CODE! USE AT YOUR OWN RISK!!
.SH "DEVICE NAMES"
The current version of the backend only allows one camera to be
connected. The device name is always "0".
.SH CONFIGURATION
The contents of the
.I dc240.conf
specify the serial port and baud rate to use. The
.B baud
rate specifies the maximum rate to use while downloading pictures. (The
camera is always initialized using 9600 baud, then switches to the
higher rate). On a 450MHz Pentium, I usually have no problems downloading
at 115200 baud, though the camera sometimes has to resend packets due
to lost characters. Results are better when
the "interrupt-unmask flag" is set in the IDE driver
.RI ( "hdparm \-u1" ).
Supported baud rates are: 9600, 19200, 38400, 57600, and 115200.
.PP
The
.B dumpinquiry
line causes some information about the camera to be printed.
.PP
.B cmdrespause
specifies how many usec (1,000,000ths of a second) to wait between
writing the command and reading the result. 125000 seems to be the
lowest I could go reliably.
.PP
.B breakpause
specifies how many usec (1,000,000ths of a second) between sending the
"back to default" break and sending commands.
.PP
Empty lines and lines starting with a hash mark (#) are
ignored. A sample configuration file is shown below:
.PP
.RS
port=/dev/ttyS0
.br
# this is a comment
.br
baud=115200
.br
dumpinquiry
.br
cmdrespause=125000
.br
breakpause=1000000
.RE
.PP
.SH FILES
.TP
.I @CONFIGDIR@/dc240.conf
The backend configuration file (see also description of
.B SANE_CONFIG_DIR
below).
.TP
.I @LIBDIR@/libsane\-dc240.a
The static library implementing this backend.
.TP
.I @LIBDIR@/libsane\-dc240.so
The shared library implementing this backend (present on systems that
support dynamic loading).
.SH ENVIRONMENT
.TP
.B SANE_CONFIG_DIR
This environment variable specifies the list of directories that may
contain the configuration file. On *NIX systems, the directories are
separated by a colon (`:'), under OS/2, they are separated by a
semi-colon (`;'). If this variable is not set, the configuration file
is searched in two default directories: first, the current working
directory (".") and then in
.I @CONFIGDIR@.
If the value of the
environment variable ends with the directory separator character, then
the default directories are searched after the explicitly specified
directories. For example, setting
.B SANE_CONFIG_DIR
to "/tmp/config:" would result in directories
.IR "tmp/config",
.IR ".",
and
.I "@CONFIGDIR@"
being searched (in this order).
.TP
.B SANE_DEBUG_DC240
If the library was compiled with debugging support enabled, this
environment variable controls the debug level for this backend.
A value of 128 requests maximally copious debug output; smaller
levels reduce verbosity.
.SH "SEE ALSO"
.BR sane (7)
.SH AUTHOR
Peter S. Fales
.PP
This backend borrows heavily from the
.BR sane\-dc210 (5)
backend by Brian J. Murrell
which is based somewhat on the
.BR sane\-dc25 (5)
backend by Peter Fales.
.PP
The manpage was largely copied from the
.BR sane\-dc210 (5)
manpage.
.SH BUGS
The major limitation that I know of is that the backend assumes
the directory in the camera is 100dc240. Once the camera has
taken more than 9999 pictures, the directory will increment to 101dc240.
Not only should we check for the additional directory, but pictures may
actually be found in multiple directories.
.PP
More general comments, suggestions, and inquiries about frontends
or SANE should go to the SANE Developers mailing list
(see
.I http://www.sane\-project.org/mailing\-lists.html
for details).
You must be subscribed to the list, otherwise your mail won't be
sent to the subscribers.
|
