1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
|
# Plustek-SANE Backend configuration file
# For use with LM9831/2/3 based USB scanners
#
# each device needs at least two lines:
# - [usb] vendor-ID and product-ID
# - device devicename
# i.e. for Plustek (0x07B3) UT12/16/24 (0x0017)
# [usb] 0x07B3 0x0017
# device /dev/usbscanner
# or
# device libusb:bbb:ddd
# where bbb is the busnumber and ddd the device number
# make sure that your user has access to /proc/bus/usb/bbb/ddd
#
# additionally you can specify some options
# warmup, lOffOnEnd, lampOff
#
# For autodetection use
# [usb]
# device /dev/usbscanner
#
# or simply
# [usb]
#
# or if you want a specific device but you have no idea about the
# device node or you use libusb, simply set vendor- and product-ID
# [usb] 0x07B3 0x0017
# device auto
#
# NOTE: autodetection is safe, as it uses the info it got
# from the USB subsystem. If you're not using the
# autodetection, you MUST have attached that device
# at your USB-port, that you have specified...
#
[usb]
#
# options for the previous USB entry
#
# switch lamp off after xxx secs, 0 disables the feature
# (can also be set via frontend)
option lampOff 300
# warmup period in seconds, 0 means no warmup, -1 means auto-warmup
# (can also be set via frontend)
option warmup -1
# 0 means leave lamp-status untouched, not 0 means switch off
# on sane_close
# (can also be set via frontend)
option lOffOnEnd 1
#
# options to tweak the image start-position
# (WARNING: there's no internal range check!!!)
#
# for the normal scan area
#
option posOffX 0
option posOffY 0
# for transparencies
option tpaOffX 0
option tpaOffY 0
# for negatives
option negOffX 0
option negOffY 0
#
# for setting the calibration strip position
# (WARNING: there's no internal range check!!!)
# -1 means use built in
# (can also be set via frontend)
option posShadingY -1
option tpaShadingY -1
option negShadingY -1
#
# to invert the negatives, 0 disables the feature
#
option invertNegatives 0
#
# to disable the internal sensor speedup function,
# 1 disables the feature
#
option disableSpeedup 0
#
# to save/restore coarse calibration data
# (can also be set via frontend)
option cacheCalData 0
#
# use alternate calibration routines
#
option altCalibration 0
#
# for skipping whole calibration step
#
option skipCalibration 0
#
# for skipping entire fine calibration step
# coarse calibration is done
#
option skipFine 0
#
# discard the result of the fine white calibration
#
option skipFineWhite 0
#
# some scanners have a dark calibration strip, in
# general this one should be used for calibration.
# As this could cause some trouble, this option
# overrides that and the dark calibration will be
# done by switching the lamp off
#
option skipDarkStrip 0
# for replacing the gain values found during coarse
# calibration
# (can also be set via frontend)
option red_gain -1
option green_gain -1
option blue_gain -1
# for replacing the offset values found during coarse
# calibration
# (can also be set via frontend)
option red_offset -1
option green_offset -1
option blue_offset -1
#
# for replacing the default lampoff settings, this
# works only for CIS devices like CanoScan LiDE20
# (can also be set via frontend)
option red_lampoff -1
option green_lampoff -1
option blue_lampoff -1
#
# for adjusting the default gamma values
# (can also be set via frontend)
option redGamma 1.0
option greenGamma 1.0
option blueGamma 1.0
option grayGamma 1.0
#
# to enable TPA (EPSON or UMAX, if autodetection fails)
# 0 means default behaviour as specified in the internal tables
# 1 means enable (needed for UMAX 3450)
option enableTPA 0
#
# model override functionality, currently only available for
# Mustek devices, using NSCs' vendor ID: 0x0400 and
# also their product ID: 0x1000 (LM9831) 0x1001 (LM9832)
#
# mov/PID | 0x1000 | 0x1001
# ---------------------------------------
# 0 (default)| BearPaw1200 | BearPaw 2400
# 1 | ignored | BearPaw 1200
#
option mov 0
#
# and of course the device-name
#
# device /dev/usbscanner
device auto
#
# to define a new device, start with a new section:
# [usb]
#
|
